BGP_LOCAL_PREF

network

(no description)

Usage diagram

The following diagram shows usage relationships between types. Unresolved types are missing from the diagram.

Properties

Name	Value	Description
isNetwork
display	bgb=1328.6062,594.495

Unassigned submodule parameters

Name	Type	Default value	Description
configurator.displayStringTextFormat	string	""	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
configurator.minLinkWeight	double	1E-3
configurator.configureIsolatedNetworksSeparatly	bool	false
configurator.config	xml	xml("")	XML configuration parameters for IP address assignment and adding manual routes
configurator.assignAddresses	bool	true	Assign IP addresses to all interfaces in the network
configurator.assignUniqueAddresses	bool	true	Avoid using the same address and raise an error if not possible
configurator.assignDisjunctSubnetAddresses	bool	true	Avoid using the same address prefix and netmask on different links when assigning IP addresses to interfaces
configurator.addStaticRoutes	bool	true	Add static routes to the routing tables of all nodes to route to all destination interfaces (only where applicable; turn off when config file contains manual routes)
configurator.addDefaultRoutes	bool	true	Add default routes if all routes from a source node go through the same gateway (used only if addStaticRoutes is true)
configurator.addSubnetRoutes	bool	true	Add subnet routes instead of destination interface routes (only where applicable; used only if addStaticRoutes is true)
configurator.addDirectRoutes	bool	true	Add direct routes towards local network members (i.e. directly connected interfaces) to the routing table (used only if addStaticRoutes is true)
configurator.optimizeRoutes	bool	true	Optimize routing tables by merging routes, the resulting routing table might route more packets than the original (used only if addStaticRoutes is true)
configurator.updateRoutes	bool	false	Recalculate static routes if an interface goes down/up or a carrier is lost/back
configurator.dumpTopology	bool	false	Print extracted network topology to the module output
configurator.dumpLinks	bool	false	Print recognized network links to the module output
configurator.dumpAddresses	bool	false	Print assigned IP addresses for all interfaces to the module output
configurator.dumpRoutes	bool	false	Print configured and optimized routing tables for all nodes to the module output
configurator.dumpConfig	string	""	Write configuration into the given config file that can be fed back to speed up subsequent runs (network configurations)
visualizer.sceneVisualizer.visualizationTargetModule	string
visualizer.sceneVisualizer.visualizationSubjectModule	string
visualizer.physicalEnvironmentVisualizer.visualizationTargetModule	string
visualizer.physicalEnvironmentVisualizer.visualizationSubjectModule	string
visualizer.networkNodeVisualizer.visualizationTargetModule	string
visualizer.networkNodeVisualizer.visualizationSubjectModule	string
visualizer.networkConnectionVisualizer.visualizationTargetModule	string
visualizer.networkConnectionVisualizer.visualizationSubjectModule	string
visualizer.mobilityVisualizer.visualizationTargetModule	string
visualizer.mobilityVisualizer.visualizationSubjectModule	string
visualizer.statisticVisualizer.visualizationTargetModule	string
visualizer.statisticVisualizer.visualizationSubjectModule	string
visualizer.infoVisualizer.visualizationTargetModule	string
visualizer.infoVisualizer.visualizationSubjectModule	string
visualizer.energyStorageVisualizer.visualizationTargetModule	string
visualizer.energyStorageVisualizer.visualizationSubjectModule	string
visualizer.mediumVisualizer.visualizationTargetModule	string
visualizer.mediumVisualizer.visualizationSubjectModule	string
visualizer.obstacleLossVisualizer.visualizationTargetModule	string
visualizer.obstacleLossVisualizer.visualizationSubjectModule	string
visualizer.packetDropVisualizer.visualizationTargetModule	string
visualizer.packetDropVisualizer.visualizationSubjectModule	string
visualizer.queueVisualizer.visualizationTargetModule	string
visualizer.queueVisualizer.visualizationSubjectModule	string
visualizer.gateScheduleVisualizer.visualizationTargetModule	string
visualizer.gateScheduleVisualizer.visualizationSubjectModule	string
visualizer.radioVisualizer.visualizationTargetModule	string
visualizer.radioVisualizer.visualizationSubjectModule	string
visualizer.physicalLinkVisualizer.visualizationTargetModule	string
visualizer.physicalLinkVisualizer.visualizationSubjectModule	string
visualizer.interfaceTableVisualizer.visualizationTargetModule	string
visualizer.interfaceTableVisualizer.visualizationSubjectModule	string
visualizer.dataLinkVisualizer.visualizationTargetModule	string
visualizer.dataLinkVisualizer.visualizationSubjectModule	string
visualizer.linkBreakVisualizer.visualizationTargetModule	string
visualizer.linkBreakVisualizer.visualizationSubjectModule	string
visualizer.ieee80211Visualizer.visualizationTargetModule	string
visualizer.ieee80211Visualizer.visualizationSubjectModule	string
visualizer.networkRouteVisualizer.visualizationTargetModule	string
visualizer.networkRouteVisualizer.visualizationSubjectModule	string
visualizer.routingTableVisualizer.visualizationTargetModule	string
visualizer.routingTableVisualizer.visualizationSubjectModule	string
visualizer.transportRouteVisualizer.visualizationTargetModule	string
visualizer.transportRouteVisualizer.visualizationSubjectModule	string
visualizer.transportConnectionVisualizer.visualizationTargetModule	string
visualizer.transportConnectionVisualizer.visualizationSubjectModule	string
visualizer.failureProtectionConfigurationVisualizer.visualizationTargetModule	string
visualizer.failureProtectionConfigurationVisualizer.visualizationSubjectModule	string
visualizer.streamRedundancyConfigurationVisualizer.visualizationTargetModule	string
visualizer.streamRedundancyConfigurationVisualizer.visualizationSubjectModule	string
routingTableRecorder.displayStringTextFormat	string	""	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
routingTableRecorder.enabled	bool	true
routingTableRecorder.logfile	string	"${resultdir}/${configname}-#${runnumber}.rt"
pcapRecorder.displayStringTextFormat	string	"rec: %n pks"	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
pcapRecorder.verbose	bool	true	Whether to log packets on the module output
pcapRecorder.recordEmptyPackets	bool	true	Specifies if zero length packets are recorded or not
pcapRecorder.enableConvertingPackets	bool	true	Specifies if converting packets to link type is allowed or not
pcapRecorder.pcapFile	string	""	The PCAP file to be written, suggested value: pcapFile = "${resultdir}/${configname}-#${runnumber}" + fullpath() + ".pcap"
pcapRecorder.fileFormat	string	"pcapng"
pcapRecorder.snaplen	int	65535	Maximum number of bytes to record per packet
pcapRecorder.timePrecision	int	6	Time precision in recorded file. pcap supports only 6 (usec) or 9 (nanosec), pcapng supports more values (see 'if_tsresol' option in pcapng file format).
pcapRecorder.dumpBadFrames	bool	true	Enable dump of frames with hasBitError
pcapRecorder.moduleNamePatterns	string	"wlan[] eth[] ppp[*]"	Space-separated list of sibling module names to listen on
pcapRecorder.sendingSignalNames	string	"transmissionEnded"	Space-separated list of outbound packet signals to subscribe to
pcapRecorder.receivingSignalNames	string	"receptionEnded"	Space-separated list of inbound packet signals to subscribe to
pcapRecorder.dumpProtocols	string	"ethernetmac ppp ieee80211mac"	Space-separated list of protocol names as defined in the Protocol class
pcapRecorder.packetFilter	object	"*"	Which packets are considered, matches all packets by default
pcapRecorder.helpers	string	""	Usable PcapRecorder::IHelper helpers for accept packettype and store/convert packet as specified linktype currently available: "inet::AckingMacToEthernetPcapRecorderHelper"
pcapRecorder.alwaysFlush	bool	false	Flush the pcapFile after each write to ensure that all packets are captured in case of a crash
RB1.status.displayStringTextFormat	string	""	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
RB1.status.initialStatus	string	"UP"	TODO @signal, @statistic
RB1.environment.displayStringTextFormat	string	""	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
RB1.environment.initStage	int	0	Initialization stage for the setup command
RB1.environment.globalNamespace	bool	false	Create new network namespaces under /var/run/netns/ (Linux only)
RB1.environment.namespace	string	""	Name of the host OS network namespace (optional) (Linux only)
RB1.environment.setupCommand	string	""	A host OS system command
RB1.environment.teardownCommand	string	""	A host OS system command
RB1.pcapRecorder.displayStringTextFormat	string	"rec: %n pks"	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
RB1.pcapRecorder.verbose	bool	true	Whether to log packets on the module output
RB1.pcapRecorder.recordEmptyPackets	bool	true	Specifies if zero length packets are recorded or not
RB1.pcapRecorder.enableConvertingPackets	bool	true	Specifies if converting packets to link type is allowed or not
RB1.pcapRecorder.pcapFile	string	""	The PCAP file to be written, suggested value: pcapFile = "${resultdir}/${configname}-#${runnumber}" + fullpath() + ".pcap"
RB1.pcapRecorder.fileFormat	string	"pcapng"
RB1.pcapRecorder.snaplen	int	65535	Maximum number of bytes to record per packet
RB1.pcapRecorder.timePrecision	int	6	Time precision in recorded file. pcap supports only 6 (usec) or 9 (nanosec), pcapng supports more values (see 'if_tsresol' option in pcapng file format).
RB1.pcapRecorder.dumpBadFrames	bool	true	Enable dump of frames with hasBitError
RB1.pcapRecorder.moduleNamePatterns	string	"wlan[] eth[] ppp[*]"	Space-separated list of sibling module names to listen on
RB1.pcapRecorder.sendingSignalNames	string	"transmissionEnded"	Space-separated list of outbound packet signals to subscribe to
RB1.pcapRecorder.receivingSignalNames	string	"receptionEnded"	Space-separated list of inbound packet signals to subscribe to
RB1.pcapRecorder.dumpProtocols	string	"ethernetmac ppp ieee80211mac"	Space-separated list of protocol names as defined in the Protocol class
RB1.pcapRecorder.packetFilter	object	"*"	Which packets are considered, matches all packets by default
RB1.pcapRecorder.helpers	string	""	Usable PcapRecorder::IHelper helpers for accept packettype and store/convert packet as specified linktype currently available: "inet::AckingMacToEthernetPcapRecorderHelper"
RB1.pcapRecorder.alwaysFlush	bool	false	Flush the pcapFile after each write to ensure that all packets are captured in case of a crash
RB1.interfaceTable.displayStringTextFormat	string	""	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
RB1.interfaceTable.displayAddresses	bool	false	Whether to display IP addresses on links
RB1.cb.displayStringTextFormat	string	"processed %p pk (%l)"	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
RB1.cb.interfaceTableModule	string		Module path to the ~InterfaceTable module
RB1.cb.forwardServiceRegistration	bool	true
RB1.cb.forwardProtocolRegistration	bool	true
RB1.cb.interfaceMapping	object	{}	Maps network interface names to connected submodule names (e.g. {"eth0": "bridging"}), overrides automatically learned dispatching; * overrides all learned network interfaces, ? overrides default
RB1.cb.serviceMapping	object	{}	Maps protocols to connected submodule names (e.g. {"ethernetmac": "bridging"}), overrides automatically learned dispatching; * overrides all learned services, ? overrides default
RB1.cb.protocolMapping	object	{}	Maps protocols to connected submodule names (e.g. {"ipv4": "bridging"}), overrides automatically learned dispatching; * overrides all learned protocols, ? overrides default
RB1.bl.displayStringTextFormat	string	"processed %p pk (%l)"	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
RB1.bl.interfaceTableModule	string		Module path to the ~InterfaceTable module
RB1.bl.forwardServiceRegistration	bool	true
RB1.bl.forwardProtocolRegistration	bool	true
RB1.bl.interfaceMapping	object	{}	Maps network interface names to connected submodule names (e.g. {"eth0": "bridging"}), overrides automatically learned dispatching; * overrides all learned network interfaces, ? overrides default
RB1.bl.serviceMapping	object	{}	Maps protocols to connected submodule names (e.g. {"ethernetmac": "bridging"}), overrides automatically learned dispatching; * overrides all learned services, ? overrides default
RB1.bl.protocolMapping	object	{}	Maps protocols to connected submodule names (e.g. {"ipv4": "bridging"}), overrides automatically learned dispatching; * overrides all learned protocols, ? overrides default
RB1.li.displayStringTextFormat	string	"processed %p pk (%l)"	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
RB1.li.interfaceTableModule	string		Module path to the ~InterfaceTable module
RB1.li.forwardServiceRegistration	bool	true
RB1.li.forwardProtocolRegistration	bool	true
RB1.li.interfaceMapping	object	{}	Maps network interface names to connected submodule names (e.g. {"eth0": "bridging"}), overrides automatically learned dispatching; * overrides all learned network interfaces, ? overrides default
RB1.li.serviceMapping	object	{}	Maps protocols to connected submodule names (e.g. {"ethernetmac": "bridging"}), overrides automatically learned dispatching; * overrides all learned services, ? overrides default
RB1.li.protocolMapping	object	{}	Maps protocols to connected submodule names (e.g. {"ipv4": "bridging"}), overrides automatically learned dispatching; * overrides all learned protocols, ? overrides default
RB1.eth.bitrate	double
RB1.nl.displayStringTextFormat	string	"processed %p pk (%l)"	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
RB1.nl.interfaceTableModule	string		Module path to the ~InterfaceTable module
RB1.nl.forwardServiceRegistration	bool	true
RB1.nl.forwardProtocolRegistration	bool	true
RB1.nl.interfaceMapping	object	{}	Maps network interface names to connected submodule names (e.g. {"eth0": "bridging"}), overrides automatically learned dispatching; * overrides all learned network interfaces, ? overrides default
RB1.nl.serviceMapping	object	{}	Maps protocols to connected submodule names (e.g. {"ethernetmac": "bridging"}), overrides automatically learned dispatching; * overrides all learned services, ? overrides default
RB1.nl.protocolMapping	object	{}	Maps protocols to connected submodule names (e.g. {"ipv4": "bridging"}), overrides automatically learned dispatching; * overrides all learned protocols, ? overrides default
RB1.tn.displayStringTextFormat	string	"processed %p pk (%l)"	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
RB1.tn.interfaceTableModule	string		Module path to the ~InterfaceTable module
RB1.tn.forwardServiceRegistration	bool	true
RB1.tn.forwardProtocolRegistration	bool	true
RB1.tn.interfaceMapping	object	{}	Maps network interface names to connected submodule names (e.g. {"eth0": "bridging"}), overrides automatically learned dispatching; * overrides all learned network interfaces, ? overrides default
RB1.tn.serviceMapping	object	{}	Maps protocols to connected submodule names (e.g. {"ethernetmac": "bridging"}), overrides automatically learned dispatching; * overrides all learned services, ? overrides default
RB1.tn.protocolMapping	object	{}	Maps protocols to connected submodule names (e.g. {"ipv4": "bridging"}), overrides automatically learned dispatching; * overrides all learned protocols, ? overrides default
RB1.at.displayStringTextFormat	string	"processed %p pk (%l)"	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
RB1.at.interfaceTableModule	string		Module path to the ~InterfaceTable module
RB1.at.forwardServiceRegistration	bool	true
RB1.at.forwardProtocolRegistration	bool	true
RB1.at.interfaceMapping	object	{}	Maps network interface names to connected submodule names (e.g. {"eth0": "bridging"}), overrides automatically learned dispatching; * overrides all learned network interfaces, ? overrides default
RB1.at.serviceMapping	object	{}	Maps protocols to connected submodule names (e.g. {"ethernetmac": "bridging"}), overrides automatically learned dispatching; * overrides all learned services, ? overrides default
RB1.at.protocolMapping	object	{}	Maps protocols to connected submodule names (e.g. {"ipv4": "bridging"}), overrides automatically learned dispatching; * overrides all learned protocols, ? overrides default
RB1.bgp.interfaceTableModule	string		The path to the InterfaceTable module
RB1.bgp.routingTableModule	string
RB1.bgp.ospfRoutingModule	string	parent.hasOspf ? "^.ospf" : ""
RB2.status.displayStringTextFormat	string	""	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
RB2.status.initialStatus	string	"UP"	TODO @signal, @statistic
RB2.environment.displayStringTextFormat	string	""	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
RB2.environment.initStage	int	0	Initialization stage for the setup command
RB2.environment.globalNamespace	bool	false	Create new network namespaces under /var/run/netns/ (Linux only)
RB2.environment.namespace	string	""	Name of the host OS network namespace (optional) (Linux only)
RB2.environment.setupCommand	string	""	A host OS system command
RB2.environment.teardownCommand	string	""	A host OS system command
RB2.pcapRecorder.displayStringTextFormat	string	"rec: %n pks"	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
RB2.pcapRecorder.verbose	bool	true	Whether to log packets on the module output
RB2.pcapRecorder.recordEmptyPackets	bool	true	Specifies if zero length packets are recorded or not
RB2.pcapRecorder.enableConvertingPackets	bool	true	Specifies if converting packets to link type is allowed or not
RB2.pcapRecorder.pcapFile	string	""	The PCAP file to be written, suggested value: pcapFile = "${resultdir}/${configname}-#${runnumber}" + fullpath() + ".pcap"
RB2.pcapRecorder.fileFormat	string	"pcapng"
RB2.pcapRecorder.snaplen	int	65535	Maximum number of bytes to record per packet
RB2.pcapRecorder.timePrecision	int	6	Time precision in recorded file. pcap supports only 6 (usec) or 9 (nanosec), pcapng supports more values (see 'if_tsresol' option in pcapng file format).
RB2.pcapRecorder.dumpBadFrames	bool	true	Enable dump of frames with hasBitError
RB2.pcapRecorder.moduleNamePatterns	string	"wlan[] eth[] ppp[*]"	Space-separated list of sibling module names to listen on
RB2.pcapRecorder.sendingSignalNames	string	"transmissionEnded"	Space-separated list of outbound packet signals to subscribe to
RB2.pcapRecorder.receivingSignalNames	string	"receptionEnded"	Space-separated list of inbound packet signals to subscribe to
RB2.pcapRecorder.dumpProtocols	string	"ethernetmac ppp ieee80211mac"	Space-separated list of protocol names as defined in the Protocol class
RB2.pcapRecorder.packetFilter	object	"*"	Which packets are considered, matches all packets by default
RB2.pcapRecorder.helpers	string	""	Usable PcapRecorder::IHelper helpers for accept packettype and store/convert packet as specified linktype currently available: "inet::AckingMacToEthernetPcapRecorderHelper"
RB2.pcapRecorder.alwaysFlush	bool	false	Flush the pcapFile after each write to ensure that all packets are captured in case of a crash
RB2.interfaceTable.displayStringTextFormat	string	""	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
RB2.interfaceTable.displayAddresses	bool	false	Whether to display IP addresses on links
RB2.cb.displayStringTextFormat	string	"processed %p pk (%l)"	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
RB2.cb.interfaceTableModule	string		Module path to the ~InterfaceTable module
RB2.cb.forwardServiceRegistration	bool	true
RB2.cb.forwardProtocolRegistration	bool	true
RB2.cb.interfaceMapping	object	{}	Maps network interface names to connected submodule names (e.g. {"eth0": "bridging"}), overrides automatically learned dispatching; * overrides all learned network interfaces, ? overrides default
RB2.cb.serviceMapping	object	{}	Maps protocols to connected submodule names (e.g. {"ethernetmac": "bridging"}), overrides automatically learned dispatching; * overrides all learned services, ? overrides default
RB2.cb.protocolMapping	object	{}	Maps protocols to connected submodule names (e.g. {"ipv4": "bridging"}), overrides automatically learned dispatching; * overrides all learned protocols, ? overrides default
RB2.bl.displayStringTextFormat	string	"processed %p pk (%l)"	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
RB2.bl.interfaceTableModule	string		Module path to the ~InterfaceTable module
RB2.bl.forwardServiceRegistration	bool	true
RB2.bl.forwardProtocolRegistration	bool	true
RB2.bl.interfaceMapping	object	{}	Maps network interface names to connected submodule names (e.g. {"eth0": "bridging"}), overrides automatically learned dispatching; * overrides all learned network interfaces, ? overrides default
RB2.bl.serviceMapping	object	{}	Maps protocols to connected submodule names (e.g. {"ethernetmac": "bridging"}), overrides automatically learned dispatching; * overrides all learned services, ? overrides default
RB2.bl.protocolMapping	object	{}	Maps protocols to connected submodule names (e.g. {"ipv4": "bridging"}), overrides automatically learned dispatching; * overrides all learned protocols, ? overrides default
RB2.li.displayStringTextFormat	string	"processed %p pk (%l)"	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
RB2.li.interfaceTableModule	string		Module path to the ~InterfaceTable module
RB2.li.forwardServiceRegistration	bool	true
RB2.li.forwardProtocolRegistration	bool	true
RB2.li.interfaceMapping	object	{}	Maps network interface names to connected submodule names (e.g. {"eth0": "bridging"}), overrides automatically learned dispatching; * overrides all learned network interfaces, ? overrides default
RB2.li.serviceMapping	object	{}	Maps protocols to connected submodule names (e.g. {"ethernetmac": "bridging"}), overrides automatically learned dispatching; * overrides all learned services, ? overrides default
RB2.li.protocolMapping	object	{}	Maps protocols to connected submodule names (e.g. {"ipv4": "bridging"}), overrides automatically learned dispatching; * overrides all learned protocols, ? overrides default
RB2.eth.bitrate	double
RB2.nl.displayStringTextFormat	string	"processed %p pk (%l)"	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
RB2.nl.interfaceTableModule	string		Module path to the ~InterfaceTable module
RB2.nl.forwardServiceRegistration	bool	true
RB2.nl.forwardProtocolRegistration	bool	true
RB2.nl.interfaceMapping	object	{}	Maps network interface names to connected submodule names (e.g. {"eth0": "bridging"}), overrides automatically learned dispatching; * overrides all learned network interfaces, ? overrides default
RB2.nl.serviceMapping	object	{}	Maps protocols to connected submodule names (e.g. {"ethernetmac": "bridging"}), overrides automatically learned dispatching; * overrides all learned services, ? overrides default
RB2.nl.protocolMapping	object	{}	Maps protocols to connected submodule names (e.g. {"ipv4": "bridging"}), overrides automatically learned dispatching; * overrides all learned protocols, ? overrides default
RB2.tn.displayStringTextFormat	string	"processed %p pk (%l)"	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
RB2.tn.interfaceTableModule	string		Module path to the ~InterfaceTable module
RB2.tn.forwardServiceRegistration	bool	true
RB2.tn.forwardProtocolRegistration	bool	true
RB2.tn.interfaceMapping	object	{}	Maps network interface names to connected submodule names (e.g. {"eth0": "bridging"}), overrides automatically learned dispatching; * overrides all learned network interfaces, ? overrides default
RB2.tn.serviceMapping	object	{}	Maps protocols to connected submodule names (e.g. {"ethernetmac": "bridging"}), overrides automatically learned dispatching; * overrides all learned services, ? overrides default
RB2.tn.protocolMapping	object	{}	Maps protocols to connected submodule names (e.g. {"ipv4": "bridging"}), overrides automatically learned dispatching; * overrides all learned protocols, ? overrides default
RB2.at.displayStringTextFormat	string	"processed %p pk (%l)"	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
RB2.at.interfaceTableModule	string		Module path to the ~InterfaceTable module
RB2.at.forwardServiceRegistration	bool	true
RB2.at.forwardProtocolRegistration	bool	true
RB2.at.interfaceMapping	object	{}	Maps network interface names to connected submodule names (e.g. {"eth0": "bridging"}), overrides automatically learned dispatching; * overrides all learned network interfaces, ? overrides default
RB2.at.serviceMapping	object	{}	Maps protocols to connected submodule names (e.g. {"ethernetmac": "bridging"}), overrides automatically learned dispatching; * overrides all learned services, ? overrides default
RB2.at.protocolMapping	object	{}	Maps protocols to connected submodule names (e.g. {"ipv4": "bridging"}), overrides automatically learned dispatching; * overrides all learned protocols, ? overrides default
RB2.bgp.interfaceTableModule	string		The path to the InterfaceTable module
RB2.bgp.routingTableModule	string
RB2.bgp.ospfRoutingModule	string	parent.hasOspf ? "^.ospf" : ""
RB3.status.displayStringTextFormat	string	""	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
RB3.status.initialStatus	string	"UP"	TODO @signal, @statistic
RB3.environment.displayStringTextFormat	string	""	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
RB3.environment.initStage	int	0	Initialization stage for the setup command
RB3.environment.globalNamespace	bool	false	Create new network namespaces under /var/run/netns/ (Linux only)
RB3.environment.namespace	string	""	Name of the host OS network namespace (optional) (Linux only)
RB3.environment.setupCommand	string	""	A host OS system command
RB3.environment.teardownCommand	string	""	A host OS system command
RB3.pcapRecorder.displayStringTextFormat	string	"rec: %n pks"	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
RB3.pcapRecorder.verbose	bool	true	Whether to log packets on the module output
RB3.pcapRecorder.recordEmptyPackets	bool	true	Specifies if zero length packets are recorded or not
RB3.pcapRecorder.enableConvertingPackets	bool	true	Specifies if converting packets to link type is allowed or not
RB3.pcapRecorder.pcapFile	string	""	The PCAP file to be written, suggested value: pcapFile = "${resultdir}/${configname}-#${runnumber}" + fullpath() + ".pcap"
RB3.pcapRecorder.fileFormat	string	"pcapng"
RB3.pcapRecorder.snaplen	int	65535	Maximum number of bytes to record per packet
RB3.pcapRecorder.timePrecision	int	6	Time precision in recorded file. pcap supports only 6 (usec) or 9 (nanosec), pcapng supports more values (see 'if_tsresol' option in pcapng file format).
RB3.pcapRecorder.dumpBadFrames	bool	true	Enable dump of frames with hasBitError
RB3.pcapRecorder.moduleNamePatterns	string	"wlan[] eth[] ppp[*]"	Space-separated list of sibling module names to listen on
RB3.pcapRecorder.sendingSignalNames	string	"transmissionEnded"	Space-separated list of outbound packet signals to subscribe to
RB3.pcapRecorder.receivingSignalNames	string	"receptionEnded"	Space-separated list of inbound packet signals to subscribe to
RB3.pcapRecorder.dumpProtocols	string	"ethernetmac ppp ieee80211mac"	Space-separated list of protocol names as defined in the Protocol class
RB3.pcapRecorder.packetFilter	object	"*"	Which packets are considered, matches all packets by default
RB3.pcapRecorder.helpers	string	""	Usable PcapRecorder::IHelper helpers for accept packettype and store/convert packet as specified linktype currently available: "inet::AckingMacToEthernetPcapRecorderHelper"
RB3.pcapRecorder.alwaysFlush	bool	false	Flush the pcapFile after each write to ensure that all packets are captured in case of a crash
RB3.interfaceTable.displayStringTextFormat	string	""	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
RB3.interfaceTable.displayAddresses	bool	false	Whether to display IP addresses on links
RB3.cb.displayStringTextFormat	string	"processed %p pk (%l)"	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
RB3.cb.interfaceTableModule	string		Module path to the ~InterfaceTable module
RB3.cb.forwardServiceRegistration	bool	true
RB3.cb.forwardProtocolRegistration	bool	true
RB3.cb.interfaceMapping	object	{}	Maps network interface names to connected submodule names (e.g. {"eth0": "bridging"}), overrides automatically learned dispatching; * overrides all learned network interfaces, ? overrides default
RB3.cb.serviceMapping	object	{}	Maps protocols to connected submodule names (e.g. {"ethernetmac": "bridging"}), overrides automatically learned dispatching; * overrides all learned services, ? overrides default
RB3.cb.protocolMapping	object	{}	Maps protocols to connected submodule names (e.g. {"ipv4": "bridging"}), overrides automatically learned dispatching; * overrides all learned protocols, ? overrides default
RB3.bl.displayStringTextFormat	string	"processed %p pk (%l)"	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
RB3.bl.interfaceTableModule	string		Module path to the ~InterfaceTable module
RB3.bl.forwardServiceRegistration	bool	true
RB3.bl.forwardProtocolRegistration	bool	true
RB3.bl.interfaceMapping	object	{}	Maps network interface names to connected submodule names (e.g. {"eth0": "bridging"}), overrides automatically learned dispatching; * overrides all learned network interfaces, ? overrides default
RB3.bl.serviceMapping	object	{}	Maps protocols to connected submodule names (e.g. {"ethernetmac": "bridging"}), overrides automatically learned dispatching; * overrides all learned services, ? overrides default
RB3.bl.protocolMapping	object	{}	Maps protocols to connected submodule names (e.g. {"ipv4": "bridging"}), overrides automatically learned dispatching; * overrides all learned protocols, ? overrides default
RB3.li.displayStringTextFormat	string	"processed %p pk (%l)"	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
RB3.li.interfaceTableModule	string		Module path to the ~InterfaceTable module
RB3.li.forwardServiceRegistration	bool	true
RB3.li.forwardProtocolRegistration	bool	true
RB3.li.interfaceMapping	object	{}	Maps network interface names to connected submodule names (e.g. {"eth0": "bridging"}), overrides automatically learned dispatching; * overrides all learned network interfaces, ? overrides default
RB3.li.serviceMapping	object	{}	Maps protocols to connected submodule names (e.g. {"ethernetmac": "bridging"}), overrides automatically learned dispatching; * overrides all learned services, ? overrides default
RB3.li.protocolMapping	object	{}	Maps protocols to connected submodule names (e.g. {"ipv4": "bridging"}), overrides automatically learned dispatching; * overrides all learned protocols, ? overrides default
RB3.eth.bitrate	double
RB3.nl.displayStringTextFormat	string	"processed %p pk (%l)"	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
RB3.nl.interfaceTableModule	string		Module path to the ~InterfaceTable module
RB3.nl.forwardServiceRegistration	bool	true
RB3.nl.forwardProtocolRegistration	bool	true
RB3.nl.interfaceMapping	object	{}	Maps network interface names to connected submodule names (e.g. {"eth0": "bridging"}), overrides automatically learned dispatching; * overrides all learned network interfaces, ? overrides default
RB3.nl.serviceMapping	object	{}	Maps protocols to connected submodule names (e.g. {"ethernetmac": "bridging"}), overrides automatically learned dispatching; * overrides all learned services, ? overrides default
RB3.nl.protocolMapping	object	{}	Maps protocols to connected submodule names (e.g. {"ipv4": "bridging"}), overrides automatically learned dispatching; * overrides all learned protocols, ? overrides default
RB3.tn.displayStringTextFormat	string	"processed %p pk (%l)"	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
RB3.tn.interfaceTableModule	string		Module path to the ~InterfaceTable module
RB3.tn.forwardServiceRegistration	bool	true
RB3.tn.forwardProtocolRegistration	bool	true
RB3.tn.interfaceMapping	object	{}	Maps network interface names to connected submodule names (e.g. {"eth0": "bridging"}), overrides automatically learned dispatching; * overrides all learned network interfaces, ? overrides default
RB3.tn.serviceMapping	object	{}	Maps protocols to connected submodule names (e.g. {"ethernetmac": "bridging"}), overrides automatically learned dispatching; * overrides all learned services, ? overrides default
RB3.tn.protocolMapping	object	{}	Maps protocols to connected submodule names (e.g. {"ipv4": "bridging"}), overrides automatically learned dispatching; * overrides all learned protocols, ? overrides default
RB3.at.displayStringTextFormat	string	"processed %p pk (%l)"	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
RB3.at.interfaceTableModule	string		Module path to the ~InterfaceTable module
RB3.at.forwardServiceRegistration	bool	true
RB3.at.forwardProtocolRegistration	bool	true
RB3.at.interfaceMapping	object	{}	Maps network interface names to connected submodule names (e.g. {"eth0": "bridging"}), overrides automatically learned dispatching; * overrides all learned network interfaces, ? overrides default
RB3.at.serviceMapping	object	{}	Maps protocols to connected submodule names (e.g. {"ethernetmac": "bridging"}), overrides automatically learned dispatching; * overrides all learned services, ? overrides default
RB3.at.protocolMapping	object	{}	Maps protocols to connected submodule names (e.g. {"ipv4": "bridging"}), overrides automatically learned dispatching; * overrides all learned protocols, ? overrides default
RB3.bgp.interfaceTableModule	string		The path to the InterfaceTable module
RB3.bgp.routingTableModule	string
RB3.bgp.ospfRoutingModule	string	parent.hasOspf ? "^.ospf" : ""
RA.status.displayStringTextFormat	string	""	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
RA.status.initialStatus	string	"UP"	TODO @signal, @statistic
RA.environment.displayStringTextFormat	string	""	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
RA.environment.initStage	int	0	Initialization stage for the setup command
RA.environment.globalNamespace	bool	false	Create new network namespaces under /var/run/netns/ (Linux only)
RA.environment.namespace	string	""	Name of the host OS network namespace (optional) (Linux only)
RA.environment.setupCommand	string	""	A host OS system command
RA.environment.teardownCommand	string	""	A host OS system command
RA.pcapRecorder.displayStringTextFormat	string	"rec: %n pks"	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
RA.pcapRecorder.verbose	bool	true	Whether to log packets on the module output
RA.pcapRecorder.recordEmptyPackets	bool	true	Specifies if zero length packets are recorded or not
RA.pcapRecorder.enableConvertingPackets	bool	true	Specifies if converting packets to link type is allowed or not
RA.pcapRecorder.pcapFile	string	""	The PCAP file to be written, suggested value: pcapFile = "${resultdir}/${configname}-#${runnumber}" + fullpath() + ".pcap"
RA.pcapRecorder.fileFormat	string	"pcapng"
RA.pcapRecorder.snaplen	int	65535	Maximum number of bytes to record per packet
RA.pcapRecorder.timePrecision	int	6	Time precision in recorded file. pcap supports only 6 (usec) or 9 (nanosec), pcapng supports more values (see 'if_tsresol' option in pcapng file format).
RA.pcapRecorder.dumpBadFrames	bool	true	Enable dump of frames with hasBitError
RA.pcapRecorder.moduleNamePatterns	string	"wlan[] eth[] ppp[*]"	Space-separated list of sibling module names to listen on
RA.pcapRecorder.sendingSignalNames	string	"transmissionEnded"	Space-separated list of outbound packet signals to subscribe to
RA.pcapRecorder.receivingSignalNames	string	"receptionEnded"	Space-separated list of inbound packet signals to subscribe to
RA.pcapRecorder.dumpProtocols	string	"ethernetmac ppp ieee80211mac"	Space-separated list of protocol names as defined in the Protocol class
RA.pcapRecorder.packetFilter	object	"*"	Which packets are considered, matches all packets by default
RA.pcapRecorder.helpers	string	""	Usable PcapRecorder::IHelper helpers for accept packettype and store/convert packet as specified linktype currently available: "inet::AckingMacToEthernetPcapRecorderHelper"
RA.pcapRecorder.alwaysFlush	bool	false	Flush the pcapFile after each write to ensure that all packets are captured in case of a crash
RA.interfaceTable.displayStringTextFormat	string	""	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
RA.interfaceTable.displayAddresses	bool	false	Whether to display IP addresses on links
RA.cb.displayStringTextFormat	string	"processed %p pk (%l)"	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
RA.cb.interfaceTableModule	string		Module path to the ~InterfaceTable module
RA.cb.forwardServiceRegistration	bool	true
RA.cb.forwardProtocolRegistration	bool	true
RA.cb.interfaceMapping	object	{}	Maps network interface names to connected submodule names (e.g. {"eth0": "bridging"}), overrides automatically learned dispatching; * overrides all learned network interfaces, ? overrides default
RA.cb.serviceMapping	object	{}	Maps protocols to connected submodule names (e.g. {"ethernetmac": "bridging"}), overrides automatically learned dispatching; * overrides all learned services, ? overrides default
RA.cb.protocolMapping	object	{}	Maps protocols to connected submodule names (e.g. {"ipv4": "bridging"}), overrides automatically learned dispatching; * overrides all learned protocols, ? overrides default
RA.bl.displayStringTextFormat	string	"processed %p pk (%l)"	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
RA.bl.interfaceTableModule	string		Module path to the ~InterfaceTable module
RA.bl.forwardServiceRegistration	bool	true
RA.bl.forwardProtocolRegistration	bool	true
RA.bl.interfaceMapping	object	{}	Maps network interface names to connected submodule names (e.g. {"eth0": "bridging"}), overrides automatically learned dispatching; * overrides all learned network interfaces, ? overrides default
RA.bl.serviceMapping	object	{}	Maps protocols to connected submodule names (e.g. {"ethernetmac": "bridging"}), overrides automatically learned dispatching; * overrides all learned services, ? overrides default
RA.bl.protocolMapping	object	{}	Maps protocols to connected submodule names (e.g. {"ipv4": "bridging"}), overrides automatically learned dispatching; * overrides all learned protocols, ? overrides default
RA.li.displayStringTextFormat	string	"processed %p pk (%l)"	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
RA.li.interfaceTableModule	string		Module path to the ~InterfaceTable module
RA.li.forwardServiceRegistration	bool	true
RA.li.forwardProtocolRegistration	bool	true
RA.li.interfaceMapping	object	{}	Maps network interface names to connected submodule names (e.g. {"eth0": "bridging"}), overrides automatically learned dispatching; * overrides all learned network interfaces, ? overrides default
RA.li.serviceMapping	object	{}	Maps protocols to connected submodule names (e.g. {"ethernetmac": "bridging"}), overrides automatically learned dispatching; * overrides all learned services, ? overrides default
RA.li.protocolMapping	object	{}	Maps protocols to connected submodule names (e.g. {"ipv4": "bridging"}), overrides automatically learned dispatching; * overrides all learned protocols, ? overrides default
RA.eth.bitrate	double
RA.nl.displayStringTextFormat	string	"processed %p pk (%l)"	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
RA.nl.interfaceTableModule	string		Module path to the ~InterfaceTable module
RA.nl.forwardServiceRegistration	bool	true
RA.nl.forwardProtocolRegistration	bool	true
RA.nl.interfaceMapping	object	{}	Maps network interface names to connected submodule names (e.g. {"eth0": "bridging"}), overrides automatically learned dispatching; * overrides all learned network interfaces, ? overrides default
RA.nl.serviceMapping	object	{}	Maps protocols to connected submodule names (e.g. {"ethernetmac": "bridging"}), overrides automatically learned dispatching; * overrides all learned services, ? overrides default
RA.nl.protocolMapping	object	{}	Maps protocols to connected submodule names (e.g. {"ipv4": "bridging"}), overrides automatically learned dispatching; * overrides all learned protocols, ? overrides default
RA.tn.displayStringTextFormat	string	"processed %p pk (%l)"	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
RA.tn.interfaceTableModule	string		Module path to the ~InterfaceTable module
RA.tn.forwardServiceRegistration	bool	true
RA.tn.forwardProtocolRegistration	bool	true
RA.tn.interfaceMapping	object	{}	Maps network interface names to connected submodule names (e.g. {"eth0": "bridging"}), overrides automatically learned dispatching; * overrides all learned network interfaces, ? overrides default
RA.tn.serviceMapping	object	{}	Maps protocols to connected submodule names (e.g. {"ethernetmac": "bridging"}), overrides automatically learned dispatching; * overrides all learned services, ? overrides default
RA.tn.protocolMapping	object	{}	Maps protocols to connected submodule names (e.g. {"ipv4": "bridging"}), overrides automatically learned dispatching; * overrides all learned protocols, ? overrides default
RA.at.displayStringTextFormat	string	"processed %p pk (%l)"	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
RA.at.interfaceTableModule	string		Module path to the ~InterfaceTable module
RA.at.forwardServiceRegistration	bool	true
RA.at.forwardProtocolRegistration	bool	true
RA.at.interfaceMapping	object	{}	Maps network interface names to connected submodule names (e.g. {"eth0": "bridging"}), overrides automatically learned dispatching; * overrides all learned network interfaces, ? overrides default
RA.at.serviceMapping	object	{}	Maps protocols to connected submodule names (e.g. {"ethernetmac": "bridging"}), overrides automatically learned dispatching; * overrides all learned services, ? overrides default
RA.at.protocolMapping	object	{}	Maps protocols to connected submodule names (e.g. {"ipv4": "bridging"}), overrides automatically learned dispatching; * overrides all learned protocols, ? overrides default
RA.bgp.interfaceTableModule	string		The path to the InterfaceTable module
RA.bgp.routingTableModule	string
RA.bgp.ospfRoutingModule	string	parent.hasOspf ? "^.ospf" : ""
switch1.macTable.agingTime	double
switch1.macTable.forwardingTableFile	string
switch1.interfaceTable.displayStringTextFormat	string	""	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
switch1.interfaceTable.displayAddresses	bool	false	Whether to display IP addresses on links
switch1.status.displayStringTextFormat	string	""	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
switch1.status.initialStatus	string	"UP"	TODO @signal, @statistic
switch1.pcapRecorder.displayStringTextFormat	string	"rec: %n pks"	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
switch1.pcapRecorder.verbose	bool	true	Whether to log packets on the module output
switch1.pcapRecorder.recordEmptyPackets	bool	true	Specifies if zero length packets are recorded or not
switch1.pcapRecorder.enableConvertingPackets	bool	true	Specifies if converting packets to link type is allowed or not
switch1.pcapRecorder.pcapFile	string	""	The PCAP file to be written, suggested value: pcapFile = "${resultdir}/${configname}-#${runnumber}" + fullpath() + ".pcap"
switch1.pcapRecorder.fileFormat	string	"pcapng"
switch1.pcapRecorder.snaplen	int	65535	Maximum number of bytes to record per packet
switch1.pcapRecorder.timePrecision	int	6	Time precision in recorded file. pcap supports only 6 (usec) or 9 (nanosec), pcapng supports more values (see 'if_tsresol' option in pcapng file format).
switch1.pcapRecorder.dumpBadFrames	bool	true	Enable dump of frames with hasBitError
switch1.pcapRecorder.moduleNamePatterns	string	"wlan[] eth[] ppp[*]"	Space-separated list of sibling module names to listen on
switch1.pcapRecorder.sendingSignalNames	string	"transmissionEnded"	Space-separated list of outbound packet signals to subscribe to
switch1.pcapRecorder.receivingSignalNames	string	"receptionEnded"	Space-separated list of inbound packet signals to subscribe to
switch1.pcapRecorder.dumpProtocols	string	"ethernetmac ppp ieee80211mac"	Space-separated list of protocol names as defined in the Protocol class
switch1.pcapRecorder.packetFilter	object	"*"	Which packets are considered, matches all packets by default
switch1.pcapRecorder.helpers	string	""	Usable PcapRecorder::IHelper helpers for accept packettype and store/convert packet as specified linktype currently available: "inet::AckingMacToEthernetPcapRecorderHelper"
switch1.pcapRecorder.alwaysFlush	bool	false	Flush the pcapFile after each write to ensure that all packets are captured in case of a crash
switch1.mrp.ccmInterval	double
switch1.mrp.mrpRole	string
switch1.mrp.timingProfile	int
switch1.mrp.uuid0	int
switch1.mrp.uuid1	int
switch1.mrp.ringPort1	int
switch1.mrp.ringPort2	int
switch1.mrp.interconnectionLinkCheckAware	bool
switch1.mrp.interconnectionRingCheckAware	bool
switch1.mrp.nonblockingMrcSupported	bool
switch1.mrp.reactOnLinkChange	bool
switch1.mrp.visualize	bool
switch1.stp.helloTime	double
switch1.stp.forwardDelay	double
switch1.stp.maxAge	double
switch1.stp.bridgePriority	int
switch1.stp.visualize	bool
switch1.gptp.gptpNodeType	string	"BRIDGE_NODE"
switch1.sc.displayStringTextFormat	string	"processed %p pk (%l)"	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
switch1.sc.interfaceTableModule	string		Module path to the ~InterfaceTable module
switch1.sc.forwardServiceRegistration	bool	true
switch1.sc.forwardProtocolRegistration	bool	true
switch1.sc.interfaceMapping	object	{}	Maps network interface names to connected submodule names (e.g. {"eth0": "bridging"}), overrides automatically learned dispatching; * overrides all learned network interfaces, ? overrides default
switch1.sc.serviceMapping	object	{}	Maps protocols to connected submodule names (e.g. {"ethernetmac": "bridging"}), overrides automatically learned dispatching; * overrides all learned services, ? overrides default
switch1.sc.protocolMapping	object	{}	Maps protocols to connected submodule names (e.g. {"ipv4": "bridging"}), overrides automatically learned dispatching; * overrides all learned protocols, ? overrides default
switch1.cb.displayStringTextFormat	string	"processed %p pk (%l)"	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
switch1.cb.interfaceTableModule	string		Module path to the ~InterfaceTable module
switch1.cb.forwardServiceRegistration	bool	true
switch1.cb.forwardProtocolRegistration	bool	true
switch1.cb.interfaceMapping	object	{}	Maps network interface names to connected submodule names (e.g. {"eth0": "bridging"}), overrides automatically learned dispatching; * overrides all learned network interfaces, ? overrides default
switch1.cb.serviceMapping	object	{}	Maps protocols to connected submodule names (e.g. {"ethernetmac": "bridging"}), overrides automatically learned dispatching; * overrides all learned services, ? overrides default
switch1.cb.protocolMapping	object	{}	Maps protocols to connected submodule names (e.g. {"ipv4": "bridging"}), overrides automatically learned dispatching; * overrides all learned protocols, ? overrides default
switch1.bl.displayStringTextFormat	string	"processed %p pk (%l)"	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
switch1.bl.interfaceTableModule	string		Module path to the ~InterfaceTable module
switch1.bl.forwardServiceRegistration	bool	true
switch1.bl.forwardProtocolRegistration	bool	true
switch1.bl.interfaceMapping	object	{}	Maps network interface names to connected submodule names (e.g. {"eth0": "bridging"}), overrides automatically learned dispatching; * overrides all learned network interfaces, ? overrides default
switch1.bl.serviceMapping	object	{}	Maps protocols to connected submodule names (e.g. {"ethernetmac": "bridging"}), overrides automatically learned dispatching; * overrides all learned services, ? overrides default
switch1.bl.protocolMapping	object	{}	Maps protocols to connected submodule names (e.g. {"ipv4": "bridging"}), overrides automatically learned dispatching; * overrides all learned protocols, ? overrides default
switch1.li.displayStringTextFormat	string	"processed %p pk (%l)"	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
switch1.li.interfaceTableModule	string		Module path to the ~InterfaceTable module
switch1.li.forwardServiceRegistration	bool	true
switch1.li.forwardProtocolRegistration	bool	true
switch1.li.interfaceMapping	object	{}	Maps network interface names to connected submodule names (e.g. {"eth0": "bridging"}), overrides automatically learned dispatching; * overrides all learned network interfaces, ? overrides default
switch1.li.serviceMapping	object	{}	Maps protocols to connected submodule names (e.g. {"ethernetmac": "bridging"}), overrides automatically learned dispatching; * overrides all learned services, ? overrides default
switch1.li.protocolMapping	object	{}	Maps protocols to connected submodule names (e.g. {"ipv4": "bridging"}), overrides automatically learned dispatching; * overrides all learned protocols, ? overrides default
switch1.eth.bitrate	double
RC.status.displayStringTextFormat	string	""	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
RC.status.initialStatus	string	"UP"	TODO @signal, @statistic
RC.environment.displayStringTextFormat	string	""	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
RC.environment.initStage	int	0	Initialization stage for the setup command
RC.environment.globalNamespace	bool	false	Create new network namespaces under /var/run/netns/ (Linux only)
RC.environment.namespace	string	""	Name of the host OS network namespace (optional) (Linux only)
RC.environment.setupCommand	string	""	A host OS system command
RC.environment.teardownCommand	string	""	A host OS system command
RC.pcapRecorder.displayStringTextFormat	string	"rec: %n pks"	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
RC.pcapRecorder.verbose	bool	true	Whether to log packets on the module output
RC.pcapRecorder.recordEmptyPackets	bool	true	Specifies if zero length packets are recorded or not
RC.pcapRecorder.enableConvertingPackets	bool	true	Specifies if converting packets to link type is allowed or not
RC.pcapRecorder.pcapFile	string	""	The PCAP file to be written, suggested value: pcapFile = "${resultdir}/${configname}-#${runnumber}" + fullpath() + ".pcap"
RC.pcapRecorder.fileFormat	string	"pcapng"
RC.pcapRecorder.snaplen	int	65535	Maximum number of bytes to record per packet
RC.pcapRecorder.timePrecision	int	6	Time precision in recorded file. pcap supports only 6 (usec) or 9 (nanosec), pcapng supports more values (see 'if_tsresol' option in pcapng file format).
RC.pcapRecorder.dumpBadFrames	bool	true	Enable dump of frames with hasBitError
RC.pcapRecorder.moduleNamePatterns	string	"wlan[] eth[] ppp[*]"	Space-separated list of sibling module names to listen on
RC.pcapRecorder.sendingSignalNames	string	"transmissionEnded"	Space-separated list of outbound packet signals to subscribe to
RC.pcapRecorder.receivingSignalNames	string	"receptionEnded"	Space-separated list of inbound packet signals to subscribe to
RC.pcapRecorder.dumpProtocols	string	"ethernetmac ppp ieee80211mac"	Space-separated list of protocol names as defined in the Protocol class
RC.pcapRecorder.packetFilter	object	"*"	Which packets are considered, matches all packets by default
RC.pcapRecorder.helpers	string	""	Usable PcapRecorder::IHelper helpers for accept packettype and store/convert packet as specified linktype currently available: "inet::AckingMacToEthernetPcapRecorderHelper"
RC.pcapRecorder.alwaysFlush	bool	false	Flush the pcapFile after each write to ensure that all packets are captured in case of a crash
RC.interfaceTable.displayStringTextFormat	string	""	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
RC.interfaceTable.displayAddresses	bool	false	Whether to display IP addresses on links
RC.cb.displayStringTextFormat	string	"processed %p pk (%l)"	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
RC.cb.interfaceTableModule	string		Module path to the ~InterfaceTable module
RC.cb.forwardServiceRegistration	bool	true
RC.cb.forwardProtocolRegistration	bool	true
RC.cb.interfaceMapping	object	{}	Maps network interface names to connected submodule names (e.g. {"eth0": "bridging"}), overrides automatically learned dispatching; * overrides all learned network interfaces, ? overrides default
RC.cb.serviceMapping	object	{}	Maps protocols to connected submodule names (e.g. {"ethernetmac": "bridging"}), overrides automatically learned dispatching; * overrides all learned services, ? overrides default
RC.cb.protocolMapping	object	{}	Maps protocols to connected submodule names (e.g. {"ipv4": "bridging"}), overrides automatically learned dispatching; * overrides all learned protocols, ? overrides default
RC.bl.displayStringTextFormat	string	"processed %p pk (%l)"	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
RC.bl.interfaceTableModule	string		Module path to the ~InterfaceTable module
RC.bl.forwardServiceRegistration	bool	true
RC.bl.forwardProtocolRegistration	bool	true
RC.bl.interfaceMapping	object	{}	Maps network interface names to connected submodule names (e.g. {"eth0": "bridging"}), overrides automatically learned dispatching; * overrides all learned network interfaces, ? overrides default
RC.bl.serviceMapping	object	{}	Maps protocols to connected submodule names (e.g. {"ethernetmac": "bridging"}), overrides automatically learned dispatching; * overrides all learned services, ? overrides default
RC.bl.protocolMapping	object	{}	Maps protocols to connected submodule names (e.g. {"ipv4": "bridging"}), overrides automatically learned dispatching; * overrides all learned protocols, ? overrides default
RC.li.displayStringTextFormat	string	"processed %p pk (%l)"	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
RC.li.interfaceTableModule	string		Module path to the ~InterfaceTable module
RC.li.forwardServiceRegistration	bool	true
RC.li.forwardProtocolRegistration	bool	true
RC.li.interfaceMapping	object	{}	Maps network interface names to connected submodule names (e.g. {"eth0": "bridging"}), overrides automatically learned dispatching; * overrides all learned network interfaces, ? overrides default
RC.li.serviceMapping	object	{}	Maps protocols to connected submodule names (e.g. {"ethernetmac": "bridging"}), overrides automatically learned dispatching; * overrides all learned services, ? overrides default
RC.li.protocolMapping	object	{}	Maps protocols to connected submodule names (e.g. {"ipv4": "bridging"}), overrides automatically learned dispatching; * overrides all learned protocols, ? overrides default
RC.eth.bitrate	double
RC.nl.displayStringTextFormat	string	"processed %p pk (%l)"	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
RC.nl.interfaceTableModule	string		Module path to the ~InterfaceTable module
RC.nl.forwardServiceRegistration	bool	true
RC.nl.forwardProtocolRegistration	bool	true
RC.nl.interfaceMapping	object	{}	Maps network interface names to connected submodule names (e.g. {"eth0": "bridging"}), overrides automatically learned dispatching; * overrides all learned network interfaces, ? overrides default
RC.nl.serviceMapping	object	{}	Maps protocols to connected submodule names (e.g. {"ethernetmac": "bridging"}), overrides automatically learned dispatching; * overrides all learned services, ? overrides default
RC.nl.protocolMapping	object	{}	Maps protocols to connected submodule names (e.g. {"ipv4": "bridging"}), overrides automatically learned dispatching; * overrides all learned protocols, ? overrides default
RC.tn.displayStringTextFormat	string	"processed %p pk (%l)"	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
RC.tn.interfaceTableModule	string		Module path to the ~InterfaceTable module
RC.tn.forwardServiceRegistration	bool	true
RC.tn.forwardProtocolRegistration	bool	true
RC.tn.interfaceMapping	object	{}	Maps network interface names to connected submodule names (e.g. {"eth0": "bridging"}), overrides automatically learned dispatching; * overrides all learned network interfaces, ? overrides default
RC.tn.serviceMapping	object	{}	Maps protocols to connected submodule names (e.g. {"ethernetmac": "bridging"}), overrides automatically learned dispatching; * overrides all learned services, ? overrides default
RC.tn.protocolMapping	object	{}	Maps protocols to connected submodule names (e.g. {"ipv4": "bridging"}), overrides automatically learned dispatching; * overrides all learned protocols, ? overrides default
RC.at.displayStringTextFormat	string	"processed %p pk (%l)"	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
RC.at.interfaceTableModule	string		Module path to the ~InterfaceTable module
RC.at.forwardServiceRegistration	bool	true
RC.at.forwardProtocolRegistration	bool	true
RC.at.interfaceMapping	object	{}	Maps network interface names to connected submodule names (e.g. {"eth0": "bridging"}), overrides automatically learned dispatching; * overrides all learned network interfaces, ? overrides default
RC.at.serviceMapping	object	{}	Maps protocols to connected submodule names (e.g. {"ethernetmac": "bridging"}), overrides automatically learned dispatching; * overrides all learned services, ? overrides default
RC.at.protocolMapping	object	{}	Maps protocols to connected submodule names (e.g. {"ipv4": "bridging"}), overrides automatically learned dispatching; * overrides all learned protocols, ? overrides default
RC.bgp.interfaceTableModule	string		The path to the InterfaceTable module
RC.bgp.routingTableModule	string
RC.bgp.ospfRoutingModule	string	parent.hasOspf ? "^.ospf" : ""
switch2.macTable.agingTime	double
switch2.macTable.forwardingTableFile	string
switch2.interfaceTable.displayStringTextFormat	string	""	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
switch2.interfaceTable.displayAddresses	bool	false	Whether to display IP addresses on links
switch2.status.displayStringTextFormat	string	""	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
switch2.status.initialStatus	string	"UP"	TODO @signal, @statistic
switch2.pcapRecorder.displayStringTextFormat	string	"rec: %n pks"	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
switch2.pcapRecorder.verbose	bool	true	Whether to log packets on the module output
switch2.pcapRecorder.recordEmptyPackets	bool	true	Specifies if zero length packets are recorded or not
switch2.pcapRecorder.enableConvertingPackets	bool	true	Specifies if converting packets to link type is allowed or not
switch2.pcapRecorder.pcapFile	string	""	The PCAP file to be written, suggested value: pcapFile = "${resultdir}/${configname}-#${runnumber}" + fullpath() + ".pcap"
switch2.pcapRecorder.fileFormat	string	"pcapng"
switch2.pcapRecorder.snaplen	int	65535	Maximum number of bytes to record per packet
switch2.pcapRecorder.timePrecision	int	6	Time precision in recorded file. pcap supports only 6 (usec) or 9 (nanosec), pcapng supports more values (see 'if_tsresol' option in pcapng file format).
switch2.pcapRecorder.dumpBadFrames	bool	true	Enable dump of frames with hasBitError
switch2.pcapRecorder.moduleNamePatterns	string	"wlan[] eth[] ppp[*]"	Space-separated list of sibling module names to listen on
switch2.pcapRecorder.sendingSignalNames	string	"transmissionEnded"	Space-separated list of outbound packet signals to subscribe to
switch2.pcapRecorder.receivingSignalNames	string	"receptionEnded"	Space-separated list of inbound packet signals to subscribe to
switch2.pcapRecorder.dumpProtocols	string	"ethernetmac ppp ieee80211mac"	Space-separated list of protocol names as defined in the Protocol class
switch2.pcapRecorder.packetFilter	object	"*"	Which packets are considered, matches all packets by default
switch2.pcapRecorder.helpers	string	""	Usable PcapRecorder::IHelper helpers for accept packettype and store/convert packet as specified linktype currently available: "inet::AckingMacToEthernetPcapRecorderHelper"
switch2.pcapRecorder.alwaysFlush	bool	false	Flush the pcapFile after each write to ensure that all packets are captured in case of a crash
switch2.mrp.ccmInterval	double
switch2.mrp.mrpRole	string
switch2.mrp.timingProfile	int
switch2.mrp.uuid0	int
switch2.mrp.uuid1	int
switch2.mrp.ringPort1	int
switch2.mrp.ringPort2	int
switch2.mrp.interconnectionLinkCheckAware	bool
switch2.mrp.interconnectionRingCheckAware	bool
switch2.mrp.nonblockingMrcSupported	bool
switch2.mrp.reactOnLinkChange	bool
switch2.mrp.visualize	bool
switch2.stp.helloTime	double
switch2.stp.forwardDelay	double
switch2.stp.maxAge	double
switch2.stp.bridgePriority	int
switch2.stp.visualize	bool
switch2.gptp.gptpNodeType	string	"BRIDGE_NODE"
switch2.sc.displayStringTextFormat	string	"processed %p pk (%l)"	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
switch2.sc.interfaceTableModule	string		Module path to the ~InterfaceTable module
switch2.sc.forwardServiceRegistration	bool	true
switch2.sc.forwardProtocolRegistration	bool	true
switch2.sc.interfaceMapping	object	{}	Maps network interface names to connected submodule names (e.g. {"eth0": "bridging"}), overrides automatically learned dispatching; * overrides all learned network interfaces, ? overrides default
switch2.sc.serviceMapping	object	{}	Maps protocols to connected submodule names (e.g. {"ethernetmac": "bridging"}), overrides automatically learned dispatching; * overrides all learned services, ? overrides default
switch2.sc.protocolMapping	object	{}	Maps protocols to connected submodule names (e.g. {"ipv4": "bridging"}), overrides automatically learned dispatching; * overrides all learned protocols, ? overrides default
switch2.cb.displayStringTextFormat	string	"processed %p pk (%l)"	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
switch2.cb.interfaceTableModule	string		Module path to the ~InterfaceTable module
switch2.cb.forwardServiceRegistration	bool	true
switch2.cb.forwardProtocolRegistration	bool	true
switch2.cb.interfaceMapping	object	{}	Maps network interface names to connected submodule names (e.g. {"eth0": "bridging"}), overrides automatically learned dispatching; * overrides all learned network interfaces, ? overrides default
switch2.cb.serviceMapping	object	{}	Maps protocols to connected submodule names (e.g. {"ethernetmac": "bridging"}), overrides automatically learned dispatching; * overrides all learned services, ? overrides default
switch2.cb.protocolMapping	object	{}	Maps protocols to connected submodule names (e.g. {"ipv4": "bridging"}), overrides automatically learned dispatching; * overrides all learned protocols, ? overrides default
switch2.bl.displayStringTextFormat	string	"processed %p pk (%l)"	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
switch2.bl.interfaceTableModule	string		Module path to the ~InterfaceTable module
switch2.bl.forwardServiceRegistration	bool	true
switch2.bl.forwardProtocolRegistration	bool	true
switch2.bl.interfaceMapping	object	{}	Maps network interface names to connected submodule names (e.g. {"eth0": "bridging"}), overrides automatically learned dispatching; * overrides all learned network interfaces, ? overrides default
switch2.bl.serviceMapping	object	{}	Maps protocols to connected submodule names (e.g. {"ethernetmac": "bridging"}), overrides automatically learned dispatching; * overrides all learned services, ? overrides default
switch2.bl.protocolMapping	object	{}	Maps protocols to connected submodule names (e.g. {"ipv4": "bridging"}), overrides automatically learned dispatching; * overrides all learned protocols, ? overrides default
switch2.li.displayStringTextFormat	string	"processed %p pk (%l)"	Determines the text that is written on top of the submodule, supports displaying pars, watches, and module-specific information
switch2.li.interfaceTableModule	string		Module path to the ~InterfaceTable module
switch2.li.forwardServiceRegistration	bool	true
switch2.li.forwardProtocolRegistration	bool	true
switch2.li.interfaceMapping	object	{}	Maps network interface names to connected submodule names (e.g. {"eth0": "bridging"}), overrides automatically learned dispatching; * overrides all learned network interfaces, ? overrides default
switch2.li.serviceMapping	object	{}	Maps protocols to connected submodule names (e.g. {"ethernetmac": "bridging"}), overrides automatically learned dispatching; * overrides all learned services, ? overrides default
switch2.li.protocolMapping	object	{}	Maps protocols to connected submodule names (e.g. {"ipv4": "bridging"}), overrides automatically learned dispatching; * overrides all learned protocols, ? overrides default
switch2.eth.bitrate	double

Source code

network BGP_LOCAL_PREF
{
    @display("bgb=1328.6062,594.495");

    submodules:
        configurator: Ipv4NetworkConfigurator {
            @display("p=93,44");
        }
        visualizer: IntegratedMultiCanvasVisualizer {
            @display("p=243.2025,43.536247");
        }
        routingTableRecorder: RoutingTableRecorder {
            @display("p=426,43");
        }
        pcapRecorder: PcapRecorder {
            @display("p=636,42");
        }
        RB1: Router {
            @display("p=730.935,58.275");
        }
        RB2: Router {
            @display("p=730.935,362.97");
        }
        RB3: Router {
            @display("p=910.755,199.8");
        }
        RA: Router {
            @display("p=546.12,199.8");
        }
        switch1: EthernetSwitch {
            @display("p=366.3,198.135");
        }
        RC: Router {
            @display("p=564.435,512.82");
        }
        switch2: EthernetSwitch {
            @display("p=366.3,511.155");
        }
    connections:
        RB1.ethg++ <--> Eth100M <--> RB3.ethg++;
        RB2.ethg++ <--> Eth100M <--> RB3.ethg++;
        RA.ethg++ <--> Eth100M <--> RB1.ethg++;
        RA.ethg++ <--> Eth100M <--> RB2.ethg++;
        RC.ethg++ <--> Eth100M <--> RB2.ethg++;
        switch1.ethg++ <--> Eth100M <--> RA.ethg++;
        RC.ethg++ <--> Eth100M <--> switch2.ethg++;
}

File: tutorials/bgp/BGP_LOCAL_PREF.ned