Network TransportPathVisualizerServerClientsShowcase

Package: inet.showcases.visualizer.transportpathactivity
File: showcases/visualizer/transportpathactivity/TransportPathVisualizerShowcase.ned

TODO documentation

IntegratedVisualizer IPv4NetworkConfigurator StandardHost StandardHost StandardHost StandardHost StandardHost EtherSwitch EtherSwitch Router

Usage diagram:

The following diagram shows usage relationships between types. Unresolved types are missing from the diagram.

Inheritance diagram:

The following diagram shows inheritance relationships for this type. Unresolved types are missing from the diagram.

Properties:

Name Value Description
isNetwork
display bgb=600,400

Unassigned submodule parameters:

Name Type Default value Description
configurator.minLinkWeight double 1E-3
configurator.config xml xml("")

XML configuration parameters for IP address assignment and adding manual routes
configurator.assignAddresses bool true

assign IP addresses to all interfaces in the network
configurator.assignDisjunctSubnetAddresses bool true

avoid using the same address prefix and netmask on different links when assigning IP addresses to interfaces
configurator.addStaticRoutes bool true

add static routes to the routing tables of all nodes to route to all destination interfaces (only where applicable; turn off when config file contains manual routes)
configurator.addDefaultRoutes bool true

add default routes if all routes from a source node go through the same gateway (used only if addStaticRoutes is true)
configurator.addSubnetRoutes bool true

add subnet routes instead of destination interface routes (only where applicable; used only if addStaticRoutes is true)
configurator.optimizeRoutes bool true

optimize routing tables by merging routes, the resulting routing table might route more packets than the original (used only if addStaticRoutes is true)
configurator.dumpTopology bool false

print extracted network topology to the module output
configurator.dumpLinks bool false

print recognized network links to the module output
configurator.dumpAddresses bool false

print assigned IP addresses for all interfaces to the module output
configurator.dumpRoutes bool false

print configured and optimized routing tables for all nodes to the module output
configurator.dumpConfig string ""

write configuration into the given config file that can be fed back to speed up subsequent runs (network configurations)
server.status.initialStatus string "UP"

TODO @signal, @statistic
server.routingTable.forwarding bool
server.routingTable.multicastForwarding bool
server.interfaceTable.displayAddresses bool false

whether to display IP addresses on links
server.pcapRecorder.verbose bool false

whether to log packets on the module output
server.pcapRecorder.pcapFile string ""

the PCAP file to be written
server.pcapRecorder.snaplen int 65535

maximum number of bytes to record per packet
server.pcapRecorder.dumpBadFrames bool true

enable dump of frames with hasBitError
server.pcapRecorder.moduleNamePatterns string "wlan[*] eth[*] ppp[*] ext[*]"

space-separated list of sibling module names to listen on
server.pcapRecorder.sendingSignalNames string "packetSentToLower"

space-separated list of outbound packet signals to subscribe to
server.pcapRecorder.receivingSignalNames string "packetReceivedFromLower"

space-separated list of inbound packet signals to subscribe to
server.pcapRecorder.alwaysFlush bool false

flush the pcapFile after each write to ensure that all packets are captured in case of a crash
server.lo0.lo.interfaceTableModule string

The path to the InterfaceTable module
server.lo0.lo.mtu int 4470B
host1.status.initialStatus string "UP"

TODO @signal, @statistic
host1.routingTable.forwarding bool
host1.routingTable.multicastForwarding bool
host1.interfaceTable.displayAddresses bool false

whether to display IP addresses on links
host1.pcapRecorder.verbose bool false

whether to log packets on the module output
host1.pcapRecorder.pcapFile string ""

the PCAP file to be written
host1.pcapRecorder.snaplen int 65535

maximum number of bytes to record per packet
host1.pcapRecorder.dumpBadFrames bool true

enable dump of frames with hasBitError
host1.pcapRecorder.moduleNamePatterns string "wlan[*] eth[*] ppp[*] ext[*]"

space-separated list of sibling module names to listen on
host1.pcapRecorder.sendingSignalNames string "packetSentToLower"

space-separated list of outbound packet signals to subscribe to
host1.pcapRecorder.receivingSignalNames string "packetReceivedFromLower"

space-separated list of inbound packet signals to subscribe to
host1.pcapRecorder.alwaysFlush bool false

flush the pcapFile after each write to ensure that all packets are captured in case of a crash
host1.lo0.lo.interfaceTableModule string

The path to the InterfaceTable module
host1.lo0.lo.mtu int 4470B
host2.status.initialStatus string "UP"

TODO @signal, @statistic
host2.routingTable.forwarding bool
host2.routingTable.multicastForwarding bool
host2.interfaceTable.displayAddresses bool false

whether to display IP addresses on links
host2.pcapRecorder.verbose bool false

whether to log packets on the module output
host2.pcapRecorder.pcapFile string ""

the PCAP file to be written
host2.pcapRecorder.snaplen int 65535

maximum number of bytes to record per packet
host2.pcapRecorder.dumpBadFrames bool true

enable dump of frames with hasBitError
host2.pcapRecorder.moduleNamePatterns string "wlan[*] eth[*] ppp[*] ext[*]"

space-separated list of sibling module names to listen on
host2.pcapRecorder.sendingSignalNames string "packetSentToLower"

space-separated list of outbound packet signals to subscribe to
host2.pcapRecorder.receivingSignalNames string "packetReceivedFromLower"

space-separated list of inbound packet signals to subscribe to
host2.pcapRecorder.alwaysFlush bool false

flush the pcapFile after each write to ensure that all packets are captured in case of a crash
host2.lo0.lo.interfaceTableModule string

The path to the InterfaceTable module
host2.lo0.lo.mtu int 4470B
admin1.status.initialStatus string "UP"

TODO @signal, @statistic
admin1.routingTable.forwarding bool
admin1.routingTable.multicastForwarding bool
admin1.interfaceTable.displayAddresses bool false

whether to display IP addresses on links
admin1.pcapRecorder.verbose bool false

whether to log packets on the module output
admin1.pcapRecorder.pcapFile string ""

the PCAP file to be written
admin1.pcapRecorder.snaplen int 65535

maximum number of bytes to record per packet
admin1.pcapRecorder.dumpBadFrames bool true

enable dump of frames with hasBitError
admin1.pcapRecorder.moduleNamePatterns string "wlan[*] eth[*] ppp[*] ext[*]"

space-separated list of sibling module names to listen on
admin1.pcapRecorder.sendingSignalNames string "packetSentToLower"

space-separated list of outbound packet signals to subscribe to
admin1.pcapRecorder.receivingSignalNames string "packetReceivedFromLower"

space-separated list of inbound packet signals to subscribe to
admin1.pcapRecorder.alwaysFlush bool false

flush the pcapFile after each write to ensure that all packets are captured in case of a crash
admin1.lo0.lo.interfaceTableModule string

The path to the InterfaceTable module
admin1.lo0.lo.mtu int 4470B
admin2.status.initialStatus string "UP"

TODO @signal, @statistic
admin2.routingTable.forwarding bool
admin2.routingTable.multicastForwarding bool
admin2.interfaceTable.displayAddresses bool false

whether to display IP addresses on links
admin2.pcapRecorder.verbose bool false

whether to log packets on the module output
admin2.pcapRecorder.pcapFile string ""

the PCAP file to be written
admin2.pcapRecorder.snaplen int 65535

maximum number of bytes to record per packet
admin2.pcapRecorder.dumpBadFrames bool true

enable dump of frames with hasBitError
admin2.pcapRecorder.moduleNamePatterns string "wlan[*] eth[*] ppp[*] ext[*]"

space-separated list of sibling module names to listen on
admin2.pcapRecorder.sendingSignalNames string "packetSentToLower"

space-separated list of outbound packet signals to subscribe to
admin2.pcapRecorder.receivingSignalNames string "packetReceivedFromLower"

space-separated list of inbound packet signals to subscribe to
admin2.pcapRecorder.alwaysFlush bool false

flush the pcapFile after each write to ensure that all packets are captured in case of a crash
admin2.lo0.lo.interfaceTableModule string

The path to the InterfaceTable module
admin2.lo0.lo.mtu int 4470B
switch1.status.initialStatus string "UP"

TODO @signal, @statistic
switch1.l2NodeConfigurator.interfaceTableModule string
switch1.l2NodeConfigurator.l2ConfiguratorModule string "l2NetworkConfigurator"

the absolute path to the L2NetworkConfigurator; use "" if there is no configurator
switch1.interfaceTable.displayAddresses bool false

whether to display IP addresses on links
switch1.macTable.agingTime double
switch1.macTable.addressTableFile string
switch1.stp.helloTime double
switch1.stp.forwardDelay double
switch1.stp.maxAge double
switch1.stp.bridgePriority int
switch1.stp.visualize bool
switch2.status.initialStatus string "UP"

TODO @signal, @statistic
switch2.l2NodeConfigurator.interfaceTableModule string
switch2.l2NodeConfigurator.l2ConfiguratorModule string "l2NetworkConfigurator"

the absolute path to the L2NetworkConfigurator; use "" if there is no configurator
switch2.interfaceTable.displayAddresses bool false

whether to display IP addresses on links
switch2.macTable.agingTime double
switch2.macTable.addressTableFile string
switch2.stp.helloTime double
switch2.stp.forwardDelay double
switch2.stp.maxAge double
switch2.stp.bridgePriority int
switch2.stp.visualize bool
router.status.initialStatus string "UP"

TODO @signal, @statistic
router.routingTable.forwarding bool
router.routingTable.multicastForwarding bool
router.interfaceTable.displayAddresses bool false

whether to display IP addresses on links
router.pcapRecorder.verbose bool false

whether to log packets on the module output
router.pcapRecorder.pcapFile string ""

the PCAP file to be written
router.pcapRecorder.snaplen int 65535

maximum number of bytes to record per packet
router.pcapRecorder.dumpBadFrames bool true

enable dump of frames with hasBitError
router.pcapRecorder.moduleNamePatterns string "wlan[*] eth[*] ppp[*] ext[*]"

space-separated list of sibling module names to listen on
router.pcapRecorder.sendingSignalNames string "packetSentToLower"

space-separated list of outbound packet signals to subscribe to
router.pcapRecorder.receivingSignalNames string "packetReceivedFromLower"

space-separated list of inbound packet signals to subscribe to
router.pcapRecorder.alwaysFlush bool false

flush the pcapFile after each write to ensure that all packets are captured in case of a crash
router.lo0.lo.interfaceTableModule string

The path to the InterfaceTable module
router.lo0.lo.mtu int 4470B
router.bgp.interfaceTableModule string

The path to the InterfaceTable module
router.bgp.routingTableModule string
router.bgp.ospfRoutingModule string hasOSPF ? "^.ospf" : ""
router.bgp.dataTransferMode string

Source code:

//
// TODO documentation
//
network TransportPathVisualizerServerClientsShowcase
{
    @display("bgb=600,400");
    submodules:
        visualizer: IntegratedVisualizer {
            parameters:
                @display("p=80,120");
        }
        configurator: IPv4NetworkConfigurator {
            parameters:
                @display("p=80,50");
        }
        server: StandardHost {
            @display("p=158,228;i=device/server2");
        }
        host1: StandardHost {
            @display("p=545,58");
        }
        host2: StandardHost {
            @display("p=545,128");
        }
        admin1: StandardHost {
            @display("p=545,341");
        }
        admin2: StandardHost {
            @display("p=545,267");
        }
        switch1: EtherSwitch {
            @display("p=414,84");
        }
        switch2: EtherSwitch {
            @display("p=414,341");
        }
        router: Router {
            @display("p=296,228");
        }
    connections:
        switch1.ethg++ <--> Eth100M <--> host1.ethg++;
        switch1.ethg++ <--> Eth100M <--> host2.ethg++;
        switch2.ethg++ <--> Eth100M <--> admin1.ethg++;
        router.ethg++ <--> Eth100M <--> switch1.ethg++;
        router.ethg++ <--> Eth100M <--> switch2.ethg++;
        server.ethg++ <--> Eth100M <--> router.ethg++;
        switch2.ethg++ <--> Eth100M <--> admin2.ethg++;
}

This documentation is released under the Creative Commons license