Network ObstacleLossVisualizationMultipleObstaclesShowcase

Package: inet.showcases.visualizer.obstacleloss
File: showcases/visualizer/obstacleloss/ObstacleLossVisualizationShowcase.ned

(no description)

AdhocHost AdhocHost IPv4NetworkConfigurator Ieee80211ScalarRadioMedium IntegratedVisualizer PhysicalEnvironment

Usage diagram:

The following diagram shows usage relationships between types. Unresolved types are missing from the diagram.

Inheritance diagram:

The following diagram shows inheritance relationships for this type. Unresolved types are missing from the diagram.

Properties:

Name Value Description
isNetwork
display bgb=800,400

Unassigned submodule parameters:

Name Type Default value Description
source.status.initialStatus string "UP"

TODO @signal, @statistic

source.routingTable.forwarding bool
source.routingTable.multicastForwarding bool
source.interfaceTable.displayAddresses bool false

whether to display IP addresses on links

source.pcapRecorder.verbose bool false

whether to log packets on the module output

source.pcapRecorder.pcapFile string ""

the PCAP file to be written

source.pcapRecorder.snaplen int 65535

maximum number of bytes to record per packet

source.pcapRecorder.dumpBadFrames bool true

enable dump of frames with hasBitError

source.pcapRecorder.moduleNamePatterns string "wlan[*] eth[*] ppp[*] ext[*]"

space-separated list of sibling module names to listen on

source.pcapRecorder.sendingSignalNames string "packetSentToLower"

space-separated list of outbound packet signals to subscribe to

source.pcapRecorder.receivingSignalNames string "packetReceivedFromLower"

space-separated list of inbound packet signals to subscribe to

source.pcapRecorder.alwaysFlush bool false

flush the pcapFile after each write to ensure that all packets are captured in case of a crash

source.lo0.lo.interfaceTableModule string

The path to the InterfaceTable module

source.lo0.lo.mtu int 4470B
destination.status.initialStatus string "UP"

TODO @signal, @statistic

destination.routingTable.forwarding bool
destination.routingTable.multicastForwarding bool
destination.interfaceTable.displayAddresses bool false

whether to display IP addresses on links

destination.pcapRecorder.verbose bool false

whether to log packets on the module output

destination.pcapRecorder.pcapFile string ""

the PCAP file to be written

destination.pcapRecorder.snaplen int 65535

maximum number of bytes to record per packet

destination.pcapRecorder.dumpBadFrames bool true

enable dump of frames with hasBitError

destination.pcapRecorder.moduleNamePatterns string "wlan[*] eth[*] ppp[*] ext[*]"

space-separated list of sibling module names to listen on

destination.pcapRecorder.sendingSignalNames string "packetSentToLower"

space-separated list of outbound packet signals to subscribe to

destination.pcapRecorder.receivingSignalNames string "packetReceivedFromLower"

space-separated list of inbound packet signals to subscribe to

destination.pcapRecorder.alwaysFlush bool false

flush the pcapFile after each write to ensure that all packets are captured in case of a crash

destination.lo0.lo.interfaceTableModule string

The path to the InterfaceTable module

destination.lo0.lo.mtu int 4470B
configurator.minLinkWeight double 1E-3
configurator.config xml xml("")

XML configuration parameters for IP address assignment and adding manual routes

configurator.assignAddresses bool true

assign IP addresses to all interfaces in the network

configurator.assignDisjunctSubnetAddresses bool true

avoid using the same address prefix and netmask on different links when assigning IP addresses to interfaces

configurator.addStaticRoutes bool true

add static routes to the routing tables of all nodes to route to all destination interfaces (only where applicable; turn off when config file contains manual routes)

configurator.addDefaultRoutes bool true

add default routes if all routes from a source node go through the same gateway (used only if addStaticRoutes is true)

configurator.addSubnetRoutes bool true

add subnet routes instead of destination interface routes (only where applicable; used only if addStaticRoutes is true)

configurator.optimizeRoutes bool true

optimize routing tables by merging routes, the resulting routing table might route more packets than the original (used only if addStaticRoutes is true)

configurator.dumpTopology bool false

print extracted network topology to the module output

configurator.dumpLinks bool false

print recognized network links to the module output

configurator.dumpAddresses bool false

print assigned IP addresses for all interfaces to the module output

configurator.dumpRoutes bool false

print configured and optimized routing tables for all nodes to the module output

configurator.dumpConfig string ""

write configuration into the given config file that can be fed back to speed up subsequent runs (network configurations)

radioMedium.neighborCache.refillPeriod double

Source code:

network ObstacleLossVisualizationMultipleObstaclesShowcase
{
    @display("bgb=800,400");
    submodules:
        source: AdhocHost {
            @display("p=200,50");
        }
        destination: AdhocHost {
            @display("p=700,350");
        }
        configurator: IPv4NetworkConfigurator {
            @display("p=88,51");
        }
        radioMedium: Ieee80211ScalarRadioMedium {
            @display("p=87,116");
        }
        visualizer: IntegratedVisualizer {
            @display("p=88,181");
        }
        physicalEnvironment: PhysicalEnvironment {
            @display("p=88,250");
        }
}