Network DataLinkVisualizerEnablingWiredShowcase

Package: inet.showcases.visualizer.datalinkactivity
File: showcases/visualizer/datalinkactivity/DatalinkVisualizerShowcase.ned

TODO documentation

Usage diagram:

The following diagram shows usage relationships between types. Unresolved types are missing from the diagram.

Inheritance diagram:

The following diagram shows inheritance relationships for this type. Unresolved types are missing from the diagram.

Properties:

Name	Value	Description
isNetwork
display	bgb=700,250

Unassigned submodule parameters:

Name	Type	Default value	Description
configurator.minLinkWeight	double	1E-3
configurator.config	xml	xml("")	XML configuration parameters for IP address assignment and adding manual routes
configurator.assignAddresses	bool	true	assign IP addresses to all interfaces in the network
configurator.assignDisjunctSubnetAddresses	bool	true	avoid using the same address prefix and netmask on different links when assigning IP addresses to interfaces
configurator.addStaticRoutes	bool	true	add static routes to the routing tables of all nodes to route to all destination interfaces (only where applicable; turn off when config file contains manual routes)
configurator.addDefaultRoutes	bool	true	add default routes if all routes from a source node go through the same gateway (used only if addStaticRoutes is true)
configurator.addSubnetRoutes	bool	true	add subnet routes instead of destination interface routes (only where applicable; used only if addStaticRoutes is true)
configurator.optimizeRoutes	bool	true	optimize routing tables by merging routes, the resulting routing table might route more packets than the original (used only if addStaticRoutes is true)
configurator.dumpTopology	bool	false	print extracted network topology to the module output
configurator.dumpLinks	bool	false	print recognized network links to the module output
configurator.dumpAddresses	bool	false	print assigned IP addresses for all interfaces to the module output
configurator.dumpRoutes	bool	false	print configured and optimized routing tables for all nodes to the module output
configurator.dumpConfig	string	""	write configuration into the given config file that can be fed back to speed up subsequent runs (network configurations)
wiredSource.status.initialStatus	string	"UP"	TODO @signal, @statistic
wiredSource.routingTable.forwarding	bool
wiredSource.routingTable.multicastForwarding	bool
wiredSource.interfaceTable.displayAddresses	bool	false	whether to display IP addresses on links
wiredSource.pcapRecorder.verbose	bool	false	whether to log packets on the module output
wiredSource.pcapRecorder.pcapFile	string	""	the PCAP file to be written
wiredSource.pcapRecorder.snaplen	int	65535	maximum number of bytes to record per packet
wiredSource.pcapRecorder.dumpBadFrames	bool	true	enable dump of frames with hasBitError
wiredSource.pcapRecorder.moduleNamePatterns	string	"wlan[] eth[] ppp[] ext[]"	space-separated list of sibling module names to listen on
wiredSource.pcapRecorder.sendingSignalNames	string	"packetSentToLower"	space-separated list of outbound packet signals to subscribe to
wiredSource.pcapRecorder.receivingSignalNames	string	"packetReceivedFromLower"	space-separated list of inbound packet signals to subscribe to
wiredSource.pcapRecorder.alwaysFlush	bool	false	flush the pcapFile after each write to ensure that all packets are captured in case of a crash
wiredSource.lo0.lo.interfaceTableModule	string		The path to the InterfaceTable module
wiredSource.lo0.lo.mtu	int	4470B
wiredDestination.status.initialStatus	string	"UP"	TODO @signal, @statistic
wiredDestination.routingTable.forwarding	bool
wiredDestination.routingTable.multicastForwarding	bool
wiredDestination.interfaceTable.displayAddresses	bool	false	whether to display IP addresses on links
wiredDestination.pcapRecorder.verbose	bool	false	whether to log packets on the module output
wiredDestination.pcapRecorder.pcapFile	string	""	the PCAP file to be written
wiredDestination.pcapRecorder.snaplen	int	65535	maximum number of bytes to record per packet
wiredDestination.pcapRecorder.dumpBadFrames	bool	true	enable dump of frames with hasBitError
wiredDestination.pcapRecorder.moduleNamePatterns	string	"wlan[] eth[] ppp[] ext[]"	space-separated list of sibling module names to listen on
wiredDestination.pcapRecorder.sendingSignalNames	string	"packetSentToLower"	space-separated list of outbound packet signals to subscribe to
wiredDestination.pcapRecorder.receivingSignalNames	string	"packetReceivedFromLower"	space-separated list of inbound packet signals to subscribe to
wiredDestination.pcapRecorder.alwaysFlush	bool	false	flush the pcapFile after each write to ensure that all packets are captured in case of a crash
wiredDestination.lo0.lo.interfaceTableModule	string		The path to the InterfaceTable module
wiredDestination.lo0.lo.mtu	int	4470B

Source code:

//
// TODO documentation
//
network DataLinkVisualizerEnablingWiredShowcase
{
    @display("bgb=700,250");
    submodules:
        linkVisualizer: DataLinkVisualizer {
            parameters:
                @display("p=100,50");
        }
        configurator: IPv4NetworkConfigurator {
            parameters:
                @display("p=100,150");
        }
        wiredSource: StandardHost {
            @display("p=300,110");
        }
        wiredDestination: StandardHost {
            @display("p=600,110");
        }
    connections:
        wiredSource.ethg++ <--> Eth100M <--> wiredDestination.ethg++;
}