Network Crosstalk

Package: inet.examples.wireless.crosstalk
File: examples/wireless/crosstalk/Crosstalk.ned

(no description)

Usage diagram:

The following diagram shows usage relationships between types. Unresolved types are missing from the diagram.

Inheritance diagram:

The following diagram shows inheritance relationships for this type. Unresolved types are missing from the diagram.

Properties:

Name	Value	Description
isNetwork
display	b=300,200

Unassigned submodule parameters:

Name	Type	Default value	Description
configurator.minLinkWeight	double	1E-3
configurator.config	xml	xml("")	XML configuration parameters for IP address assignment and adding manual routes
configurator.assignAddresses	bool	true	assign IP addresses to all interfaces in the network
configurator.assignDisjunctSubnetAddresses	bool	true	avoid using the same address prefix and netmask on different links when assigning IP addresses to interfaces
configurator.addStaticRoutes	bool	true	add static routes to the routing tables of all nodes to route to all destination interfaces (only where applicable; turn off when config file contains manual routes)
configurator.addDefaultRoutes	bool	true	add default routes if all routes from a source node go through the same gateway (used only if addStaticRoutes is true)
configurator.addSubnetRoutes	bool	true	add subnet routes instead of destination interface routes (only where applicable; used only if addStaticRoutes is true)
configurator.optimizeRoutes	bool	true	optimize routing tables by merging routes, the resulting routing table might route more packets than the original (used only if addStaticRoutes is true)
configurator.dumpTopology	bool	false	print extracted network topology to the module output
configurator.dumpLinks	bool	false	print recognized network links to the module output
configurator.dumpAddresses	bool	false	print assigned IP addresses for all interfaces to the module output
configurator.dumpRoutes	bool	false	print configured and optimized routing tables for all nodes to the module output
configurator.dumpConfig	string	""	write configuration into the given config file that can be fed back to speed up subsequent runs (network configurations)
radioMedium.neighborCache.refillPeriod	double
aNode.status.initialStatus	string	"UP"	TODO @signal, @statistic
aNode.routingTable.forwarding	bool
aNode.routingTable.multicastForwarding	bool
aNode.interfaceTable.displayAddresses	bool	false	whether to display IP addresses on links
aNode.pcapRecorder.verbose	bool	false	whether to log packets on the module output
aNode.pcapRecorder.pcapFile	string	""	the PCAP file to be written
aNode.pcapRecorder.snaplen	int	65535	maximum number of bytes to record per packet
aNode.pcapRecorder.dumpBadFrames	bool	true	enable dump of frames with hasBitError
aNode.pcapRecorder.moduleNamePatterns	string	"wlan[] eth[] ppp[] ext[]"	space-separated list of sibling module names to listen on
aNode.pcapRecorder.sendingSignalNames	string	"packetSentToLower"	space-separated list of outbound packet signals to subscribe to
aNode.pcapRecorder.receivingSignalNames	string	"packetReceivedFromLower"	space-separated list of inbound packet signals to subscribe to
aNode.pcapRecorder.alwaysFlush	bool	false	flush the pcapFile after each write to ensure that all packets are captured in case of a crash
aNode.lo0.lo.interfaceTableModule	string		The path to the InterfaceTable module
aNode.lo0.lo.mtu	int	4470B
bNode.status.initialStatus	string	"UP"	TODO @signal, @statistic
bNode.routingTable.forwarding	bool
bNode.routingTable.multicastForwarding	bool
bNode.interfaceTable.displayAddresses	bool	false	whether to display IP addresses on links
bNode.pcapRecorder.verbose	bool	false	whether to log packets on the module output
bNode.pcapRecorder.pcapFile	string	""	the PCAP file to be written
bNode.pcapRecorder.snaplen	int	65535	maximum number of bytes to record per packet
bNode.pcapRecorder.dumpBadFrames	bool	true	enable dump of frames with hasBitError
bNode.pcapRecorder.moduleNamePatterns	string	"wlan[] eth[] ppp[] ext[]"	space-separated list of sibling module names to listen on
bNode.pcapRecorder.sendingSignalNames	string	"packetSentToLower"	space-separated list of outbound packet signals to subscribe to
bNode.pcapRecorder.receivingSignalNames	string	"packetReceivedFromLower"	space-separated list of inbound packet signals to subscribe to
bNode.pcapRecorder.alwaysFlush	bool	false	flush the pcapFile after each write to ensure that all packets are captured in case of a crash
bNode.lo0.lo.interfaceTableModule	string		The path to the InterfaceTable module
bNode.lo0.lo.mtu	int	4470B

Source code:

network Crosstalk
{
    parameters:
        @display("b=300,200");
    submodules:
        visualizer: <default("IntegratedCanvasVisualizer")> like IIntegratedVisualizer if hasVisualizer() {
            parameters:
                @display("p=100,50");
        }
        configurator: IPv4NetworkConfigurator {
            parameters:
                @display("p=100,150");
        }
        radioMedium: Ieee80211DimensionalRadioMedium {
            parameters:
                @display("p=100,250");
        }
        aNode[2]: AdhocHost {
            parameters:
                @display("r=,,#707070");
        }
        bNode[2]: AdhocHost {
            parameters:
                @display("r=,,#707070");
        }
}