Network ClientServer

Package: inet.examples.inet.tcpclientserver
File: examples/inet/tcpclientserver/ClientServer.ned

(no description)

StandardHost StandardHost IPv4NetworkConfigurator NetAnimTrace

Usage diagram:

The following diagram shows usage relationships between types. Unresolved types are missing from the diagram.

Inheritance diagram:

The following diagram shows inheritance relationships for this type. Unresolved types are missing from the diagram.

Parameters:

Name Type Default value Description
per double 0

Properties:

Name Value Description
isNetwork
display bgb=232,193

Unassigned submodule parameters:

Name Type Default value Description
client1.status.initialStatus string "UP"

TODO @signal, @statistic

client1.routingTable.forwarding bool
client1.routingTable.multicastForwarding bool
client1.interfaceTable.displayAddresses bool false

whether to display IP addresses on links

client1.pcapRecorder.verbose bool false

whether to log packets on the module output

client1.pcapRecorder.pcapFile string ""

the PCAP file to be written

client1.pcapRecorder.snaplen int 65535

maximum number of bytes to record per packet

client1.pcapRecorder.dumpBadFrames bool true

enable dump of frames with hasBitError

client1.pcapRecorder.moduleNamePatterns string "wlan[*] eth[*] ppp[*] ext[*]"

space-separated list of sibling module names to listen on

client1.pcapRecorder.sendingSignalNames string "packetSentToLower"

space-separated list of outbound packet signals to subscribe to

client1.pcapRecorder.receivingSignalNames string "packetReceivedFromLower"

space-separated list of inbound packet signals to subscribe to

client1.pcapRecorder.alwaysFlush bool false

flush the pcapFile after each write to ensure that all packets are captured in case of a crash

client1.lo0.lo.interfaceTableModule string

The path to the InterfaceTable module

client1.lo0.lo.mtu int 4470B
server.status.initialStatus string "UP"

TODO @signal, @statistic

server.routingTable.forwarding bool
server.routingTable.multicastForwarding bool
server.interfaceTable.displayAddresses bool false

whether to display IP addresses on links

server.pcapRecorder.verbose bool false

whether to log packets on the module output

server.pcapRecorder.pcapFile string ""

the PCAP file to be written

server.pcapRecorder.snaplen int 65535

maximum number of bytes to record per packet

server.pcapRecorder.dumpBadFrames bool true

enable dump of frames with hasBitError

server.pcapRecorder.moduleNamePatterns string "wlan[*] eth[*] ppp[*] ext[*]"

space-separated list of sibling module names to listen on

server.pcapRecorder.sendingSignalNames string "packetSentToLower"

space-separated list of outbound packet signals to subscribe to

server.pcapRecorder.receivingSignalNames string "packetReceivedFromLower"

space-separated list of inbound packet signals to subscribe to

server.pcapRecorder.alwaysFlush bool false

flush the pcapFile after each write to ensure that all packets are captured in case of a crash

server.lo0.lo.interfaceTableModule string

The path to the InterfaceTable module

server.lo0.lo.mtu int 4470B
configurator.minLinkWeight double 1E-3
configurator.config xml xml("")

XML configuration parameters for IP address assignment and adding manual routes

configurator.assignAddresses bool true

assign IP addresses to all interfaces in the network

configurator.assignDisjunctSubnetAddresses bool true

avoid using the same address prefix and netmask on different links when assigning IP addresses to interfaces

configurator.addStaticRoutes bool true

add static routes to the routing tables of all nodes to route to all destination interfaces (only where applicable; turn off when config file contains manual routes)

configurator.addDefaultRoutes bool true

add default routes if all routes from a source node go through the same gateway (used only if addStaticRoutes is true)

configurator.addSubnetRoutes bool true

add subnet routes instead of destination interface routes (only where applicable; used only if addStaticRoutes is true)

configurator.optimizeRoutes bool true

optimize routing tables by merging routes, the resulting routing table might route more packets than the original (used only if addStaticRoutes is true)

configurator.dumpTopology bool false

print extracted network topology to the module output

configurator.dumpLinks bool false

print recognized network links to the module output

configurator.dumpAddresses bool false

print assigned IP addresses for all interfaces to the module output

configurator.dumpRoutes bool false

print configured and optimized routing tables for all nodes to the module output

configurator.dumpConfig string ""

write configuration into the given config file that can be fed back to speed up subsequent runs (network configurations)

netAnimTrace.enabled bool true
netAnimTrace.filename string "netanim-trace.txt"

Source code:

network ClientServer
{
    parameters:
        double per = default(0);
        @display("bgb=232,193");
    types:
        channel C extends DatarateChannel
        {
            datarate = 10Mbps;
            delay = 0.1us;
            per = per;
        }
    submodules:
        client1: StandardHost {
            parameters:
                @display("p=53,67;i=device/pc3");
        }
        server: StandardHost {
            parameters:
                @display("p=181,67;i=device/pc2");
        }
        configurator: IPv4NetworkConfigurator {
            parameters:
                @display("p=53,134");
        }
        netAnimTrace: NetAnimTrace {
            @display("p=184,142");
        }
    connections:
        client1.pppg++ <--> C <--> server.pppg++;
}