Network WirelessNetWith2DHCP

Package: inet.examples.dhcp
File: examples/dhcp/WirelessNetWith2DHCP.ned

(no description)

IIntegratedVisualizer Ieee80211ScalarRadioMedium WirelessHost AccessPoint StandardHost AccessPoint StandardHost IPv4NetworkConfigurator StandardHost

Usage diagram:

The following diagram shows usage relationships between types. Unresolved types are missing from the diagram.

Inheritance diagram:

The following diagram shows inheritance relationships for this type. Unresolved types are missing from the diagram.

Parameters:

Name Type Default value Description
numHosts int

Properties:

Name Value Description
isNetwork
display bgb=590,407;bgl=2

Unassigned submodule parameters:

Name Type Default value Description
radioMedium.neighborCache.refillPeriod double
client.status.initialStatus string "UP"

TODO @signal, @statistic
client.routingTable.forwarding bool
client.routingTable.multicastForwarding bool
client.interfaceTable.displayAddresses bool false

whether to display IP addresses on links
client.pcapRecorder.verbose bool false

whether to log packets on the module output
client.pcapRecorder.pcapFile string ""

the PCAP file to be written
client.pcapRecorder.snaplen int 65535

maximum number of bytes to record per packet
client.pcapRecorder.dumpBadFrames bool true

enable dump of frames with hasBitError
client.pcapRecorder.moduleNamePatterns string "wlan[*] eth[*] ppp[*] ext[*]"

space-separated list of sibling module names to listen on
client.pcapRecorder.sendingSignalNames string "packetSentToLower"

space-separated list of outbound packet signals to subscribe to
client.pcapRecorder.receivingSignalNames string "packetReceivedFromLower"

space-separated list of inbound packet signals to subscribe to
client.pcapRecorder.alwaysFlush bool false

flush the pcapFile after each write to ensure that all packets are captured in case of a crash
client.lo0.lo.interfaceTableModule string

The path to the InterfaceTable module
client.lo0.lo.mtu int 4470B
ap1.status.initialStatus string "UP"

TODO @signal, @statistic
ap1.interfaceTable.displayAddresses bool false

whether to display IP addresses on links
ap1.macTable.agingTime double
ap1.macTable.addressTableFile string
dhcpServer1.status.initialStatus string "UP"

TODO @signal, @statistic
dhcpServer1.routingTable.forwarding bool
dhcpServer1.routingTable.multicastForwarding bool
dhcpServer1.interfaceTable.displayAddresses bool false

whether to display IP addresses on links
dhcpServer1.pcapRecorder.verbose bool false

whether to log packets on the module output
dhcpServer1.pcapRecorder.pcapFile string ""

the PCAP file to be written
dhcpServer1.pcapRecorder.snaplen int 65535

maximum number of bytes to record per packet
dhcpServer1.pcapRecorder.dumpBadFrames bool true

enable dump of frames with hasBitError
dhcpServer1.pcapRecorder.moduleNamePatterns string "wlan[*] eth[*] ppp[*] ext[*]"

space-separated list of sibling module names to listen on
dhcpServer1.pcapRecorder.sendingSignalNames string "packetSentToLower"

space-separated list of outbound packet signals to subscribe to
dhcpServer1.pcapRecorder.receivingSignalNames string "packetReceivedFromLower"

space-separated list of inbound packet signals to subscribe to
dhcpServer1.pcapRecorder.alwaysFlush bool false

flush the pcapFile after each write to ensure that all packets are captured in case of a crash
dhcpServer1.lo0.lo.interfaceTableModule string

The path to the InterfaceTable module
dhcpServer1.lo0.lo.mtu int 4470B
ap2.status.initialStatus string "UP"

TODO @signal, @statistic
ap2.interfaceTable.displayAddresses bool false

whether to display IP addresses on links
ap2.macTable.agingTime double
ap2.macTable.addressTableFile string
dhcpServer2.status.initialStatus string "UP"

TODO @signal, @statistic
dhcpServer2.routingTable.forwarding bool
dhcpServer2.routingTable.multicastForwarding bool
dhcpServer2.interfaceTable.displayAddresses bool false

whether to display IP addresses on links
dhcpServer2.pcapRecorder.verbose bool false

whether to log packets on the module output
dhcpServer2.pcapRecorder.pcapFile string ""

the PCAP file to be written
dhcpServer2.pcapRecorder.snaplen int 65535

maximum number of bytes to record per packet
dhcpServer2.pcapRecorder.dumpBadFrames bool true

enable dump of frames with hasBitError
dhcpServer2.pcapRecorder.moduleNamePatterns string "wlan[*] eth[*] ppp[*] ext[*]"

space-separated list of sibling module names to listen on
dhcpServer2.pcapRecorder.sendingSignalNames string "packetSentToLower"

space-separated list of outbound packet signals to subscribe to
dhcpServer2.pcapRecorder.receivingSignalNames string "packetReceivedFromLower"

space-separated list of inbound packet signals to subscribe to
dhcpServer2.pcapRecorder.alwaysFlush bool false

flush the pcapFile after each write to ensure that all packets are captured in case of a crash
dhcpServer2.lo0.lo.interfaceTableModule string

The path to the InterfaceTable module
dhcpServer2.lo0.lo.mtu int 4470B
configurator.minLinkWeight double 1E-3
configurator.config xml xml("")

XML configuration parameters for IP address assignment and adding manual routes
configurator.assignAddresses bool true

assign IP addresses to all interfaces in the network
configurator.assignDisjunctSubnetAddresses bool true

avoid using the same address prefix and netmask on different links when assigning IP addresses to interfaces
configurator.addStaticRoutes bool true

add static routes to the routing tables of all nodes to route to all destination interfaces (only where applicable; turn off when config file contains manual routes)
configurator.addDefaultRoutes bool true

add default routes if all routes from a source node go through the same gateway (used only if addStaticRoutes is true)
configurator.addSubnetRoutes bool true

add subnet routes instead of destination interface routes (only where applicable; used only if addStaticRoutes is true)
configurator.optimizeRoutes bool true

optimize routing tables by merging routes, the resulting routing table might route more packets than the original (used only if addStaticRoutes is true)
configurator.dumpTopology bool false

print extracted network topology to the module output
configurator.dumpLinks bool false

print recognized network links to the module output
configurator.dumpAddresses bool false

print assigned IP addresses for all interfaces to the module output
configurator.dumpRoutes bool false

print configured and optimized routing tables for all nodes to the module output
configurator.dumpConfig string ""

write configuration into the given config file that can be fed back to speed up subsequent runs (network configurations)
server.status.initialStatus string "UP"

TODO @signal, @statistic
server.routingTable.forwarding bool
server.routingTable.multicastForwarding bool
server.interfaceTable.displayAddresses bool false

whether to display IP addresses on links
server.pcapRecorder.verbose bool false

whether to log packets on the module output
server.pcapRecorder.pcapFile string ""

the PCAP file to be written
server.pcapRecorder.snaplen int 65535

maximum number of bytes to record per packet
server.pcapRecorder.dumpBadFrames bool true

enable dump of frames with hasBitError
server.pcapRecorder.moduleNamePatterns string "wlan[*] eth[*] ppp[*] ext[*]"

space-separated list of sibling module names to listen on
server.pcapRecorder.sendingSignalNames string "packetSentToLower"

space-separated list of outbound packet signals to subscribe to
server.pcapRecorder.receivingSignalNames string "packetReceivedFromLower"

space-separated list of inbound packet signals to subscribe to
server.pcapRecorder.alwaysFlush bool false

flush the pcapFile after each write to ensure that all packets are captured in case of a crash
server.lo0.lo.interfaceTableModule string

The path to the InterfaceTable module
server.lo0.lo.mtu int 4470B

Source code:

network WirelessNetWith2DHCP
{
    @display("bgb=590,407;bgl=2");
    int numHosts;
    submodules:
        visualizer: <default("IntegratedCanvasVisualizer")> like IIntegratedVisualizer if hasVisualizer() {
            @display("p=305,35");
        }
        radioMedium: Ieee80211ScalarRadioMedium {
            @display("p=64,34");
        }
        client: WirelessHost {
            @display("p=64,124");
        }
        ap1: AccessPoint {
            @display("p=64,238");
        }
        dhcpServer1: StandardHost {
            @display("p=64,307");
        }
        ap2: AccessPoint {
            @display("p=511,231");
        }
        dhcpServer2: StandardHost {
            @display("p=511,307");
        }
        configurator: IPv4NetworkConfigurator {
            @display("p=180,35");
        }
        server: StandardHost {
            @display("p=283,363");
        }
    connections:
        dhcpServer1.ethg++ <--> Eth100M <--> ap1.ethg++;
        dhcpServer2.ethg++ <--> Eth100M <--> ap2.ethg++;
        dhcpServer1.ethg++ <--> Eth100M <--> server.ethg++;
        dhcpServer2.ethg++ <--> Eth100M <--> server.ethg++;
}

This documentation is released under the Creative Commons license