Network WirelessA

Package: inet.tutorials.wireless
File: tutorials/wireless/WirelessA.ned

(no description)

Usage diagram:

The following diagram shows usage relationships between types. Unresolved types are missing from the diagram.

Inheritance diagram:

The following diagram shows inheritance relationships for this type. Unresolved types are missing from the diagram.

Known subclasses:

Name	Type	Description
WirelessB	network	(no description)

Parameters:

Name	Type	Default value	Description
hostType	string	"WirelessHost"
mediumType	string	"IdealRadioMedium"

Properties:

Name	Value	Description
isNetwork
display	bgb=650,500;bgg=100,1,grey95

Signals:

Name	Type	Unit
hostB_rcvdPk

Statistics:

Name	Title	Source	Record	Unit	Interpolation Mode
rcvdPk		hostB_rcvdPk	figure(count)

Unassigned submodule parameters:

Name	Type	Default value	Description
configurator.minLinkWeight	double	1E-3
configurator.config	xml	xml("")	XML configuration parameters for IP address assignment and adding manual routes
configurator.assignAddresses	bool	true	assign IP addresses to all interfaces in the network
configurator.assignDisjunctSubnetAddresses	bool	true	avoid using the same address prefix and netmask on different links when assigning IP addresses to interfaces
configurator.addStaticRoutes	bool	true	add static routes to the routing tables of all nodes to route to all destination interfaces (only where applicable; turn off when config file contains manual routes)
configurator.addDefaultRoutes	bool	true	add default routes if all routes from a source node go through the same gateway (used only if addStaticRoutes is true)
configurator.addSubnetRoutes	bool	true	add subnet routes instead of destination interface routes (only where applicable; used only if addStaticRoutes is true)
configurator.optimizeRoutes	bool	true	optimize routing tables by merging routes, the resulting routing table might route more packets than the original (used only if addStaticRoutes is true)
configurator.dumpTopology	bool	false	print extracted network topology to the module output
configurator.dumpLinks	bool	false	print recognized network links to the module output
configurator.dumpAddresses	bool	false	print assigned IP addresses for all interfaces to the module output
configurator.dumpRoutes	bool	false	print configured and optimized routing tables for all nodes to the module output
configurator.dumpConfig	string	""	write configuration into the given config file that can be fed back to speed up subsequent runs (network configurations)

Source code:

network WirelessA
{
    parameters:
        string hostType = default("WirelessHost");
        string mediumType = default("IdealRadioMedium");

        @display("bgb=650,500;bgg=100,1,grey95");
        @figure[title](type=label; pos=0,-1; anchor=sw; color=darkblue);

        @figure[rcvdPkText](type=indicatorText; pos=420,20; anchor=w; font=,20; textFormat="packets received: %g"; initialValue=0);
        @statistic[rcvdPk](source=hostB_rcvdPk; record=figure(count); targetFigure=rcvdPkText);
        @signal[hostB_rcvdPk];
        @delegatesignal[rcvdPk](source=hostB.udpApp[0].rcvdPk; target=hostB_rcvdPk);

    submodules:
        visualizer: <default("IntegratedCanvasVisualizer")> like IIntegratedVisualizer if hasVisualizer() {
            @display("p=580,125");
        }
        configurator: IPv4NetworkConfigurator {
            @display("p=580,200");
        }
        radioMedium: <mediumType> like IRadioMedium {
            @display("p=580,275");
        }
        figureHelper: DelegateSignalConfigurator {
            @display("p=580,350");
        }
        hostA: <hostType> like INetworkNode {
            @display("p=50,325");
        }
        hostB: <hostType> like INetworkNode {
            @display("p=450,325");
        }
}

//##### (marker for doxygen)